Wear protective gloves. Sharp areas on the parts may injure your hands.
89952
1.REMOVE OCCUPANT DETECTION ECU
73230
2.REMOVE FRONT SEAT INNER BELT ASSEMBLY RH
71073S
3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER
Disconnect the rubber band of the separate type front seatback cover.
72494
4.REMOVE VERTICAL ADJUSTING HANDLE RH
| *a | Protective Tape |
|
Remove in this Direction |
Operate the vertical adjusting handle RH and using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the vertical adjusting handle RH as shown in the illustration.
72551B
5.REMOVE RECLINING HINGE COVER RH
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
Disengage the guide to remove the reclining hinge cover RH.
72525A
6.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
Remove the reclining adjuster release handle RH.
71848A
7.REMOVE SEAT ADJUSTER COVER CAP RH
| *a | Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws as shown in the illustration.
Disengage the 2 guides to remove the seat adjuster cover cap RH as shown in the illustration.
71811D
8.REMOVE FRONT SEAT CUSHION SHIELD RH
Disengage the 2 claws.
Disengage the claw and 2 guides.
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and slightly pull the front seat cushion shield RH as shown in the illustration.
|
Remove in this Direction |
Disengage the guide to remove the front seat cushion shield RH as shown in the illustration.
71861
9.REMOVE FRONT SEAT INNER CUSHION SHIELD RH
Disengage the 2 claws.
|
Remove in this Direction |
Disengage the 2 claws and 2 guides to remove the front seat inner cushion shield RH as shown in the illustration.
72136A
10.REMOVE LOWER NO. 2 SEAT TRACK SPACER
Disengage the claw and guide to remove the lower No. 2 seat track spacer from the front seat inner cushion shield RH.
72136
11.REMOVE LOWER NO. 1 SEAT TRACK SPACER
Disengage the claw and guide to remove the lower No. 1 seat track spacer from the front seat cushion shield RH.
12.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Disengage the 2 hooks.
Disconnect the connector.
Disengage the clamp.
Disengage the claw and 4 clamps to separate the front seat airbag assembly RH wire harness.
Disengage the 4 clamps first.
Remove the 4 bolts.
Disengage the 4 guides to remove the separate type front seatback assembly from the separate type front seat cushion assembly.
71931
13.REMOVE FRONT SEAT HEADREST SUPPORT
Disengage the 3 hooks.
Disengage the clamp.
Open the 2 fasteners.
Disengage the 4 claws and remove the 2 front seat headrest supports.
14.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Remove the separate type front seatback cover with pad.
71073S
15.REMOVE SEPARATE TYPE FRONT SEATBACK COVER
Using a screwdriver, disengage the 9 claws and remove the separate type front seatback cover from the separate type front seatback pad as shown in the illustration.
| *a | Screwdriver | - | - |
87510M
16.REMOVE FRONT SEATBACK HEATER ASSEMBLY RH
73910A
17.REMOVE FRONT SEAT AIRBAG ASSEMBLY RH
71053S
18.REMOVE FRONT SEATBACK SPRING SUB-ASSEMBLY RH
Disengage the 2 claws to separate the 2 front seatback edge protectors from the front seatback frame sub-assembly RH.
|
Remove in this Direction |
Remove the front seatback spring sub-assembly RH from the front seatback frame sub-assembly RH as shown in the illustration.
71587
19.REMOVE FRONT SEATBACK EDGE PROTECTOR
Remove the 2 front seatback edge protectors from the front seatback spring sub-assembly RH.
71759C
20.REMOVE FRONT NO. 1 SEATBACK HOOK
Remove the 2 front No. 1 seatback hooks from the front seatback frame sub-assembly RH.
21.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Disconnect the connector and disengage the clamp.
Disengage the 2 hooks.
Disengage the 10 hooks and remove the separate type front seat cushion cover with pad from the separate type front seat cushion spring assembly.
71071S
22.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
Using a screwdriver, disengage the 14 claws and remove the separate type front seat cushion cover from the separate type front seat cushion pad as shown in the illustration.
| *a | Screwdriver | - | - |
87510K
23.REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY RH
71876F
24.REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER LH
Disengage the 4 claws to remove the RH seat reclining adjuster inside cover LH.
71875F
25.REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure as for the LH side.
71874
26.REMOVE FRONT SEAT LOWER CUSHION SHIELD LH
| *a | Hook |
| *b | Guide |
Disengage the hook.
Disengage the claw and guide to remove the front seat lower cushion shield LH.
71873
27.REMOVE FRONT SEAT LOWER CUSHION SHIELD RH
| *a | Hook |
| *b | Guide |
Disengage the hook.
Disengage the claw and guide to remove the front seat lower cushion shield RH.
87501A
28.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH
82191
29.REMOVE FRONT SEAT WIRE
Disconnect each connector and disengage each clamp to remove the front seat wire.
82191A
30.REMOVE FRONT SEAT WIRE RH
Disconnect each connector and disengage each clamp to remove the front seat wire RH.
7181A
31.REMOVE FRONT SEAT CUSHION WIRE HARNESS HOLDER RH
Remove the 2 screws.
Disengage the claw to remove the front seat cushion wire harness holder RH.
71051A
32.REMOVE FRONT SEAT CUSHION SPRING SUB-ASSEMBLY RH
Disengage the 6 hooks to remove the front seat cushion spring sub-assembly RH from the front seat adjuster assembly RH.
72211
33.REMOVE SEAT TRACK ADJUSTING HANDLE
Disengage the 2 claws to remove the seat track adjusting handle from the front seat adjuster assembly RH.
72031
34.REMOVE FRONT SEAT VERTICAL ADJUSTER ASSEMBLY
Remove the front seat vertical adjuster assembly.
Remove the 3 nuts and vertical adjuster plate.
Remove the vertical adjuster spacer.
Remove the front vertical adjuster brake sub-assembly RH.
72497B
35.REMOVE VERTICAL ADJUSTER BRACKET COVER RH
Disengage the claw to remove the vertical adjuster bracket cover RH from the front vertical adjuster brake sub-assembly RH.