Wear protective gloves. Sharp areas on the parts may injure your hands.
72497B
1.INSTALL VERTICAL ADJUSTER BRACKET COVER RH
Engage the claw to install the vertical adjuster bracket cover RH to the front vertical adjuster brake sub-assembly RH.
72031
2.INSTALL FRONT SEAT VERTICAL ADJUSTER ASSEMBLY
Install the front seat vertical adjuster assembly.
| *a | Stud Bolt of the Front Vertical Adjuster Brake Sub-assembly RH |
| *b | Hole of the Front Seat Adjuster Assembly RH |
Install the front vertical adjuster brake sub-assembly RH.
Make sure to insert the stud bolt of the front vertical adjuster brake sub-assembly RH into the hole of the front seat adjuster assembly as shown in the illustration.
Install the vertical adjuster spacer.
Install the vertical adjuster plate with the 3 nuts.
Tighten the nuts in the order shown in the illustration.
72211
3.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the 2 claws to install the seat track adjusting handle to the front seat adjuster assembly RH.
71051A
4.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY RH
Engage the 6 hooks to install the front seat cushion spring sub-assembly RH to the front seat adjuster assembly RH.
7181A
5.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER RH
Engage the claw.
Install the front seat cushion wire harness holder RH with the 2 screws.
82191A
6.INSTALL FRONT SEAT WIRE RH
Connect each connector and engage each clamp to install the front seat wire RH.
82191
7.INSTALL FRONT SEAT WIRE
Connect each connector and engage each clamp to install the front seat wire.
87501A
8.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH
71874
9.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
| *a | Hook |
| *b | Guide |
Engage the claw and guide to install the front seat lower cushion shield LH.
Engage the hook.
71873
10.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
| *a | Hook |
| *b | Guide |
Engage the claw and guide to install the front seat lower cushion shield RH.
Engage the hook.
71876F
11.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER LH
Engage the 4 claws to install the RH seat reclining adjuster inside cover LH.
71875F
12.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure as for the LH side.
87510K
13.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH
71071S
14.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Engage the 14 claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.
15.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage the 10 hooks to install the separate type front seat cushion cover with pad to the separate type front seat cushion spring assembly.
Engage the 2 hooks.
Connect the connector and engage the clamp.
71759C
16.INSTALL FRONT NO. 1 SEATBACK HOOK
Install the 2 front No. 1 seatback hooks to the front seatback frame sub-assembly RH.
71587
17.INSTALL FRONT SEATBACK EDGE PROTECTOR
Install the 2 front seatback edge protectors to the front seatback spring sub-assembly RH.
71053S
18.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY RH
|
Install in this Direction |
Install the front seatback spring sub-assembly RH to the front seatback frame sub-assembly RH as shown in the illustration.
Engage the 2 claws to install the 2 front seatback edge protectors to the front seatback frame sub-assembly RH.
73910A
19.INSTALL FRONT SEAT AIRBAG ASSEMBLY RH
87510M
20.INSTALL FRONT SEATBACK HEATER ASSEMBLY RH
71073S
21.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Engage the 9 claws to install the separate type front seatback cover to the separate type front seatback pad.
22.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad.
71931
23.INSTALL FRONT SEAT HEADREST SUPPORT
Engage the 4 claws to install the 2 front seat headrest supports.
Close the 2 fasteners.
Engage the clamp.
Engage the 3 hooks.
24.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the 4 guides.
Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.
Engage the claw and 4 clamps to install the front seat airbag assembly RH wire harness.
Engage the claw first.
Engage the clamp.
Connect the connector.
Engage the 2 hooks.
Pass the separate type front seatback cover through the grooves of the RH seat reclining adjuster inside cover LH and RH seat reclining adjuster inside cover RH.
72136A
25.INSTALL LOWER NO. 2 SEAT TRACK SPACER
Engage the claw and guide to install the lower No. 2 seat track spacer to the front seat inner cushion shield RH.
72136
26.INSTALL LOWER NO. 1 SEAT TRACK SPACER
Engage the claw and guide to install the lower No. 1 seat track spacer to the front seat cushion shield RH.
71861
27.INSTALL FRONT SEAT INNER CUSHION SHIELD RH
|
Install in this Direction |
Engage the 2 claws and 2 guides as shown in the illustration.
Engage the 2 claws to install the front seat inner cushion shield RH.
71811D
28.INSTALL FRONT SEAT CUSHION SHIELD RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the 3 claws and 2 guides (B) as shown in the illustration.
Engage the 2 claws to install the front seat cushion shield RH.
71848A
29.INSTALL SEAT ADJUSTER COVER CAP RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the 2 guides as shown in the illustration.
Engage the 2 claws to install the seat adjuster cover cap RH as shown in the illustration.
72525A
30.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
Install the reclining adjuster release handle RH.
72552B
31.INSTALL RECLINING HINGE COVER RH
Engage the guide.
Engage the claw to install the reclining hinge cover RH.
72494
32.INSTALL VERTICAL ADJUSTING HANDLE RH
|
Install in this Direction |
Engage the claw to install the vertical adjusting handle RH as shown in the illustration.
71073S
33.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
73230
34.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH
89952
35.INSTALL OCCUPANT DETECTION ECU