Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2017.09–2021.02
RM33C0E _56 Audio / Visual / Telematics _065450 AUDIO / VIDEO _0333622 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna malfunction
·

Navigation Antenna Assembly

·

Antenna cord sub-assembly (for navigation antenna)

·

Radio and display receiver assembly


B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna power source malfunction
·

Navigation Antenna Assembly

·

Antenna cord sub-assembly (for navigation antenna)

·

Radio and display receiver assembly



WIRING DIAGRAM

E362443E11
4.969,3.063 6.656,3.656 1.688,0.594 10 false Radio and Display Receiver Assembly 0.615,1.323 2.656,1.74 2.042,0.417 10 false Navigation Antenna Assembly 0.438,3.167 4.146,3.542 3.708,0.375 10 false *: Antenna Cord Sub-assembly (for Navigation Antenna) 0.594,1.104 1.156,1.438 0.563,0.333 10 false A 4.906,2.854 5.469,3.188 0.563,0.333 10 false B 4.958,0.5 5.417,0.875 0.458,0.375 10 false 1 1.844,0.49 2.302,0.865 0.458,0.375 10 false 3 3.406,1.24 3.844,1.594 0.438,0.354 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.


·

Check that the antenna cord sub-assembly (for navigation antenna) cable is properly installed and does not have any sharp bends, pinching or loose connections before performing following procedure.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)
2.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)
a.

Remove the antenna cord sub-assembly (for navigation antenna).

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>ANTENNA CORD>REMOVAL


b.
E322997C05
0.5,1.188 0.917,1.438 0.417,0.25 0.656,3.479 1.073,3.729 0.417,0.25 1.927,3.76 2.344,3.344 false 1.854,1 2.271,0.583 false 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.354,3.177 2.667,3.375 0.313,0.198 10 false 1a 2.313,0.427 2.625,0.625 0.313,0.198 10 false 3a 0.656,1.229 0.969,1.427 0.313,0.198 10 false A 0.813,3.521 1.125,3.719 0.313,0.198 10 false B
*a Component without harness connected
(Antenna cord sub-assembly (for Navigation Antenna))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-1 Always Below 1 Ω
A-3a - B-1a Always Below 1 Ω
A-3 or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

b.
E381436C03
1.083,1.177 1.635,0.771 false 0.969,1.167 1.281,1.365 0.313,0.198 10 false 3a 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Navigation Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 3a Always 50 to 500 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG