If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.
for 6 Speakers
for 9 Speakers
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 9 Speakers | B |
A
B
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Disconnect the K4 radio and display receiver assembly connector.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-1 (FR+) - K7-4 (TWR+) | Always | Below 1 Ω |
| K4-6 (FR-) - K7-2 (TWR-) | Always | Below 1 Ω |
| K4-2 (FL+) - K8-4 (TWL+) | Always | Below 1 Ω |
| K4-7 (FL-) - K8-2 (TWL-) | Always | Below 1 Ω |
| N1-2 - K7-3 (+) | Always | Below 1 Ω |
| N1-1 - K7-1 (-) | Always | Below 1 Ω |
| O1-2 - K8-3 (+) | Always | Below 1 Ω |
| O1-1 - K8-1 (-) | Always | Below 1 Ω |
| K4-1 (FR+) or K7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K4-6 (FR-) or K7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| K4-2 (FL+) or K8-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K4-7 (FL-) or K8-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| N1-2 or K7-3 (+) - Body ground | Always | 10 kΩ or higher |
| N1-1 or K7-1 (-) - Body ground | Always | 10 kΩ or higher |
| O1-2 or K8-3 (+) - Body ground | Always | 10 kΩ or higher |
| O1-1 or K8-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K4 radio and display receiver assembly connector.
Disconnect the Q1 and P1 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-4 (RR+) - P1-1 | Always | Below 1 Ω |
| K4-9 (RR-) - P1-2 | Always | Below 1 Ω |
| K4-3 (RL+) - Q1-1 | Always | Below 1 Ω |
| K4-8 (RL-) - Q1-2 | Always | Below 1 Ω |
| K4-4 (RR+) or P1-1 - Body ground | Always | 10 kΩ or higher |
| K4-9 (RR-) or P1-2 - Body ground | Always | 10 kΩ or higher |
| K4-3 (RL+) or Q1-1 - Body ground | Always | 10 kΩ or higher |
| K4-8 (RL-) or Q1-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 3 speaker assembly | A |
| Front No. 2 speaker assembly | B |
| Rear speaker assembly | C |
| Rear stereo component speaker assembly | D |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-15 (FR+) - K109-4 (+TW) | Always | Below 1 Ω |
| K14-30 (FR-) - K109-2 (-TW) | Always | Below 1 Ω |
| K14-13 (FL+) - K110-4 (+TW) | Always | Below 1 Ω |
| K14-28 (FL-) - K110-2 (-TW) | Always | Below 1 Ω |
| N1-2 - K109-3 (+) | Always | Below 1 Ω |
| N1-1 - K109-1 (-) | Always | Below 1 Ω |
| O1-2 - K110-3 (+) | Always | Below 1 Ω |
| O1-1 - K110-1 (-) | Always | Below 1 Ω |
| K14-15 (FR+) or K109-4 (+TW) - Body ground | Always | 10 kΩ or higher |
| K14-30 (FR-) or K109-2 (-TW) - Body ground | Always | 10 kΩ or higher |
| K14-13 (FL+) or K110-4 (+TW) - Body ground | Always | 10 kΩ or higher |
| K14-28 (FL-) or K110-2 (-TW) - Body ground | Always | 10 kΩ or higher |
| N1-2 or K109-3 (+) - Body ground | Always | 10 kΩ or higher |
| N1-1 or K109-1 (-) - Body ground | Always | 10 kΩ or higher |
| O1-2 or K110-3 (+) - Body ground | Always | 10 kΩ or higher |
| O1-1 or K110-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Inspect the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-14 (TWR+) - K94-2 (TWR+) | Always | Below 1 Ω |
| K14-29 (TWR-) - K94-1 (TWR-) | Always | Below 1 Ω |
| K14-12 (TWL+) - K95-2 (TWL+) | Always | Below 1 Ω |
| K14-27 (TWL-) - K95-1 (TWL-) | Always | Below 1 Ω |
| K14-14 (TWR+) or K94-2 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K14-29 (TWR-) or K94-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| K14-12 (TWL+) or K95-2 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K14-27 (TWL-) or K95-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the P1 and Q1 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-11 (RR+) - P1-1 | Always | Below 1 Ω |
| K14-26 (RR-) - P1-2 | Always | Below 1 Ω |
| K14-9 (RL+) - Q1-1 | Always | Below 1 Ω |
| K14-24 (RL-) - Q1-2 | Always | Below 1 Ω |
| K14-11 (RR+) or P1-1 - Body ground | Always | 10 kΩ or higher |
| K14-26 (RR-) or P1-2 - Body ground | Always | 10 kΩ or higher |
| K14-9 (RL+) or Q1-1 - Body ground | Always | 10 kΩ or higher |
| K14-24 (RL-) or Q1-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the R1 rear stereo component speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-10 (WF1+) - R1-4 (WF1+) | Always | Below 1 Ω |
| K14-25 (WF1-) - R1-3 (WF1-) | Always | Below 1 Ω |
| K14-8 (WF2+) - R1-2 (WF2+) | Always | Below 1 Ω |
| K14-23 (WF2-) - R1-1 (WF2-) | Always | Below 1 Ω |
| K14-10 (WF1+) or R1-4 (WF1+) - Body ground | Always | 10 kΩ or higher |
| K14-25 (WF1-) or R1-3 (WF1-) - Body ground | Always | 10 kΩ or higher |
| K14-8 (WF2+) or R1-2 (WF2+) - Body ground | Always | 10 kΩ or higher |
| K14-23 (WF2-) or R1-1 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear stereo component speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>REMOVAL
Inspect the rear stereo component speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG