Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › PANORAMIC MOON ROOF SYSTEM
RM33C0E _59 Vehicle Exterior _065468 SLIDING ROOF / CONVERTIBLE _0333641 PANORAMIC MOON ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  PANORAMIC MOON ROOF SYSTEM  B2341  Sensor (Motor) Failure  B2344  Position Failure  


DESCRIPTION

When the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) detects a motor malfunction and the sliding roof and roof sunshade operation is stopped, DTC B2341 is stored.

When the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) detects a gear position malfunction and the sliding roof and roof sunshade operation is stopped, DTC B2344 is stored.

Sliding Roof
DTC No. Detection Item DTC Detection Condition Trouble Area
B2341 Sensor (Motor) Failure Sensor (motor) failure (When the sliding roof ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the motor)
·

Sliding roof ECU (Sliding roof drive gear assembly)

·

Panoramic moon roof switch (Roof console box sub-assembly)

·

Wire harness or connector


B2344 Position Failure Position failure (When the sliding roof ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the gear position)
·

Sliding roof ECU (Sliding roof drive gear assembly)

·

Panoramic moon roof switch (Roof console box sub-assembly)

·

Wire harness or connector



Sliding Sunshade
DTC No. Detection Item DTC Detection Condition Trouble Area
B2341 Sensor (Motor) Failure Sensor (motor) failure (When the roof sunshade ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the motor)
·

Roof sunshade ECU (Sliding roof drive gear assembly)

·

Panoramic moon roof switch (Roof console box sub-assembly)

·

Wire harness or connector


B2344 Position Failure Position failure (When the roof sunshade ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the gear position)
·

Roof sunshade ECU (Sliding roof drive gear assembly)

·

Panoramic moon roof switch (Roof console box sub-assembly)

·

Wire harness or connector



WIRING DIAGRAM

B480063E02
2.052,0.458 2.552,0.74 0.5,0.281 10 false OPN 2.073,0.854 2.573,1.135 0.5,0.281 10 false CLS 2.229,1.823 2.729,2.104 0.5,0.281 10 false B 2.167,2.615 2.667,2.896 0.5,0.281 10 false UP 1.917,2.979 2.417,3.26 0.5,0.281 10 false DOWN 2.031,4.042 2.531,4.323 0.5,0.281 10 false GND 0.219,4.667 0.719,4.948 0.5,0.281 10 false V14 0.208,4.844 2.406,5.354 2.198,0.51 10 false Panoramic Moon Roof Switch (Roof Console Box Sub-assembly) 0.708,3.26 1.667,3.646 0.958,0.385 10 false Roof Sunshade Switch 0.865,2.094 1.708,2.375 0.844,0.281 10 false Tilt Switch 0.813,1.115 1.583,1.469 0.771,0.354 10 false Sliding Roof Switch 2.458,0.448 2.958,0.729 0.5,0.281 10 false 5 2.458,0.833 2.958,1.115 0.5,0.281 10 false 4 2.427,1.813 2.927,2.094 0.5,0.281 10 false 19 2.458,2.604 2.958,2.885 0.5,0.281 10 false 3 2.417,2.969 2.917,3.25 0.5,0.281 10 false 18 2.438,4.021 2.938,4.302 0.5,0.281 10 false 15 4.927,3.438 5.427,3.719 0.5,0.281 10 false o1 4.917,3.604 6.823,4 1.906,0.396 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly) 4.958,6.781 5.458,7.063 0.5,0.281 10 false o2 4.958,6.938 6.76,7.292 1.802,0.354 10 false Roof Sunshade ECU (Sliding Roof Drive Gear Assembly) 5.198,3.094 6.271,3.281 1.073,0.188 10 false SHADE CLOSE 5.198,2.719 6.219,2.969 1.021,0.25 10 false SHADE OPEN 6.563,3.01 7.063,3.292 0.5,0.281 10 false E 5.208,1.938 5.708,2.219 0.5,0.281 10 false VENT 5.198,0.948 6.313,1.24 1.115,0.292 10 false ROOF CLOSE 5.208,0.563 6.146,0.792 0.938,0.229 10 false ROOF OPEN 4.927,0.469 5.427,0.75 0.5,0.281 10 false 10 4.979,0.844 5.479,1.125 0.5,0.281 10 false 8 5,1.844 5.5,2.125 0.5,0.281 10 false 4 5,2.615 5.5,2.896 0.5,0.281 10 false 5 4.99,2.979 5.49,3.26 0.5,0.281 10 false 9 6.76,2.885 7.115,3.146 0.354,0.26 10 false 2 4.99,6.323 5.49,6.604 0.5,0.281 10 false 9 5,5.917 5.5,6.198 0.5,0.281 10 false 5 5,5.51 5.5,5.792 0.5,0.281 10 false 4 5,5.104 5.5,5.385 0.5,0.281 10 false 8 4.938,4.688 5.438,4.969 0.5,0.281 10 false 10 6.771,6.333 7.125,6.594 0.354,0.26 10 false 2 6.552,6.438 7.052,6.719 0.5,0.281 10 false E 5.177,6.427 6.25,6.615 1.073,0.188 10 false SHADE CLOSE 5.198,6.021 6.219,6.271 1.021,0.25 10 false SHADE OPEN 5.208,5.615 5.708,5.896 0.5,0.281 10 false VENT 5.188,5.229 6.302,5.521 1.115,0.292 10 false ROOF CLOSE 5.188,4.802 6.125,5.031 0.938,0.229 10 false ROOF OPEN

CAUTION / NOTICE / HINT

NOTICE:
·

If the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION

·

DTCs B2341 and B2344 are stored in the sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly).



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147
Body Electrical > Sliding Sunshade > Clear DTCs
50002 370

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
Body Electrical > Sliding Sunshade > Trouble Codes
50001 370
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Check the parts from which this DTC has been output.


Result:
Result Proceed to
DTC output from sliding roof ECU (sliding roof drive gear assembly) A
DTC output from roof sunshade ECU (sliding roof drive gear assembly) B



A

3.CHECK SLIDING ROOF OPERATION

B

9.CHECK ROOF SUNSHADE OPERATION
3.CHECK SLIDING ROOF OPERATION
a.

Check the sliding roof auto operation function.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>OPERATION CHECK

OK:

Auto operation function operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

5.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

5.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Check that the sliding roof ECU (sliding roof drive gear assembly) can be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION

OK:

Sliding roof ECU (sliding roof drive gear assembly) can be initialized.



Result:
Proceed to
OK
NG



OK

6.CHECK DTC OUTPUT

NG

7.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY GROUND)
6.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

END (MALFUNCTION DUE TO INITIALIZATION FAILURE)

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY GROUND)
a.

Disconnect the o1 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Disconnect the V14 panoramic moon roof switch (roof console box sub-assembly) connector.


c.

Disconnect the o2 roof sunshade ECU (sliding roof drive gear assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o1-8 (ROOF CLOSE) - V14-4 (CLS) Always Below 1 Ω
o1-8 (ROOF CLOSE) or V14-4 (CLS) - Body ground Always 10 kΩ or higher
o1-10 (ROOF OPEN) - V14-5 (OPN) Always Below 1 Ω
o1-10 (ROOF OPEN) or V14-5 (OPN) - Body ground Always 10 kΩ or higher
o1-4 (VENT) - V14-19 (B) Always Below 1 Ω
o1-4 (VENT) or V14-19 (B) - Body ground Always 10 kΩ or higher
o1-5 (SHADE OPEN) - V14-3 (UP) Always Below 1 Ω
o1-5 (SHADE OPEN) or V14-3 (UP) - Body ground Always 10 kΩ or higher
o1-9 (SHADE CLOSE) - V14-18 (DOWN) Always Below 1 Ω
o1-9 (SHADE CLOSE) or V14-18 (DOWN) - Body ground Always 10 kΩ or higher
o1-2 (E) - Body ground Always Below 1 Ω
V14-15 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Remove the panoramic moon roof switch (roof console box sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the panoramic moon roof switch (roof console box sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPLACE PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)

9.CHECK ROOF SUNSHADE OPERATION
a.

Check the roof sunshade auto operation function.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>OPERATION CHECK

OK:

Auto operation function operates normally.



Result:
Proceed to
OK
NG



OK

10.CHECK DTC OUTPUT

NG

11.INITIALIZE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
10.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Sliding Sunshade > Clear DTCs
50002 370

b.

Check for DTCs.

Body Electrical > Sliding Sunshade > Trouble Codes
50001 370
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

11.INITIALIZE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Check that the roof sunshade ECU (sliding roof drive gear assembly) can be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION

OK:

Roof sunshade ECU (sliding roof drive gear assembly) can be initialized.



Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT

NG

13.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY GROUND)
12.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Sliding Sunshade > Clear DTCs
50002 370

b.

Check for DTCs.

Body Electrical > Sliding Sunshade > Trouble Codes
50001 370
OK:

DTCs B2341 and B2344 are not output.



Result:
Proceed to
OK
NG



OK

END (MALFUNCTION DUE TO INITIALIZATION FAILURE)

NG

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

13.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY GROUND)
a.

Disconnect the o2 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Disconnect the V14 panoramic moon roof switch (roof console box sub-assembly) connector.


c.

Disconnect the o1 sliding roof ECU (sliding roof drive gear assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o2-8 (ROOF CLOSE) - V14-4 (CLS) Always Below 1 Ω
o2-8 (ROOF CLOSE) or V14-4 (CLS) - Body ground Always 10 kΩ or higher
o2-10 (ROOF OPEN) - V14-5 (OPN) Always Below 1 Ω
o2-10 (ROOF OPEN) or V14-5 (OPN) - Body ground Always 10 kΩ or higher
o2-4 (VENT) - V14-19 (B) Always Below 1 Ω
o2-4 (VENT) or V14-19 (B) - Body ground Always 10 kΩ or higher
o2-5 (SHADE OPEN) - V14-3 (UP) Always Below 1 Ω
o2-5 (SHADE OPEN) or V14-3 (UP) - Body ground Always 10 kΩ or higher
o2-9 (SHADE CLOSE) - V14-18 (DOWN) Always Below 1 Ω
o2-9 (SHADE CLOSE) or V14-18 (DOWN) - Body ground Always 10 kΩ or higher
o2-2 (E) - Body ground Always Below 1 Ω
V14-15 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.INSPECT PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Remove the panoramic moon roof switch (roof console box sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the panoramic moon roof switch (roof console box sub-assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPLACE PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)