This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal as a result of its self check.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Back Camera Disconnected | Open or short in the rear television camera assembly signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Radio and display receiver assembly |
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the m1 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-30 (CA+) - m1-6 (CB+) | Always | Below 1 Ω |
| K2-28 (V+) - m1-3 (CV+) | Always | Below 1 Ω |
| K2-29 (V-) - m1-2 (CV-) | Always | Below 1 Ω |
| K2-27 (CGND) - m1-5 (CGND) | Always | Below 1 Ω |
| K2-26 (CSLD) - Body ground | Always | Below 1 Ω |
| K2-30 (CA+) or m1-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| K2-28 (V+) or m1-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| K2-29 (V-) or m1-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| K2-27 (CGND) or m1-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the K2 radio and display receiver assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-29 (V-) - Body ground | Always | Below 1 Ω |
| K2-27 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-30 (CA+) - K2-27 (CGND) | Power switch on (ACC) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the m1 rear television camera assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
| *a | Waveform 1 (camera lens is not covered, displaying an image) |
| *b | Waveform 2 (camera lens is covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
Using an oscilloscope, check the waveform of the rear television camera assembly.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
Waveform is similar to that shown in the illustration.
| Item | Content |
|---|---|
| Measurement terminal | K2-28 (V+) - K3-1 (GND1) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Power switch on (IG), shift lever in R |
The video waveform changes according to the image sent by the rear television camera assembly.
The video waveform is constantly output when the power switch is turned on (ACC).
| Proceed to |
|---|
| OK |
| NG |
OK
NG