The No. 1 blower damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air inlet damper to the appropriate position to change the air inlet mode (fresh, recirculation/fresh, and recirculation).
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1442 | Air Inlet Damper Control Servo Motor Circuit | Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly | ·
No. 1 blower damper servo sub-assembly ·
No. 1 air conditioning radiator damper servo sub-assembly ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly ·
Blower assembly |
Memorized
(30 sec. or more)* |
*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | No. 1 blower damper servo sub-assembly operating | ○ | ○ |
| Malfunction | Air inlet damper servo operation request signals are output but the air inlet damper position sensor value does not change | ○ | - |
| Air inlet damper servo operation request signals are output but the air inlet damper position sensor value is abnormal | - | ○ | |
| Detection Time | Continuously for 30 seconds or more | Continuously for 30 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
If the conditions of either of these patterns are detected, a DTC will be stored.
for LHD
for RHD
Confirm that no mechanical problems are present because this DTC can be stored when either a damper link or damper is mechanically locked.
When installing a damper servo motor, make sure to install it correctly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>REASSEMBLY
After replacing a damper servo motor, make sure to perform Servo Motor Initialization.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LHD (for 3 Zone Type) | A |
| for LHD (except 3 Zone Type) | B |
| for RHD | C |
A
B
C
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B1497 is output | A |
| B1441, B1442, B1446 and B1448 are output | B |
| Only B1442 is output | C |
A
B
C
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B1497 is output | A |
| B1441, B1442, B1443 and B1446 are output | B |
| Only B1442 is output | C |
A
B
C
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B1497 is output | A |
| B1441, B1442, B1443 and B1446 are output | B |
| Only B1442 is output | C |
A
B
C
Check that the No. 1 blower damper servo sub-assembly is installed correctly.
The No. 1 blower damper servo sub-assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 blower damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY
Operate the air inlet dampers by hand.
The air inlet dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-6 (STE2) - B-3 (sigB) | Always | Below 1 Ω |
| A-5 (STE1) - B-2 (sigA) | Always | Below 1 Ω |
| A-8 (M-) - B-5 (M-) | Always | Below 1 Ω |
| A-7 (M+) - B-4 (M+) | Always | Below 1 Ω |
| A-4 (GND) - B-1 (GND) | Always | Below 1 Ω |
| A-6 (STE2) or B-3 (sigB) - Other terminals and Body ground | Always | 10 kΩ or higher |
| A-5 (STE1) or B-2 (sigA) - Other terminals and Body ground | Always | 10 kΩ or higher |
| A-8 (M-) or B-5 (M-) - Other terminals and Body ground | Always | 10 kΩ or higher |
| A-7 (M+) or B-4 (M+) - Other terminals and Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the No. 1 air conditioning radiator damper servo sub-assembly connector.
Remove the No. 2 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Connect the No. 1 blower damper servo sub-assembly connector to the No. 2 air conditioning radiator damper servo sub-assembly.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Inlet Damper Targ Pulse | No. 1 blower damper servo sub-assembly pulse* | Min.: 128
Max.: 383 |
for 2-tier Type
Operates between 220 to 256 pulses for 1-tier Type
Operates between 235 to 258 pulses |
*: Though this Active Test is for the No. 1 blower damper servo sub-assembly, in this case it is used to check the operation of the No. 2 air conditioning radiator damper servo sub-assembly.
| Tester Display |
|---|
| Air Inlet Damper Targ Pulse |
The No. 2 air conditioning radiator damper servo sub-assembly operates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG