Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for RHD) › from 2018.04
RM33C0E _54 Brake _065443 BRAKE SYSTEM (OTHER) _0319354 BRAKE BOOSTER PUMP(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for RHD)  INSTALLATION  


PROCEDURE

Hide 47070 1.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
C378032C01
2.188,0.833 2.344,0.833 true 2.792,0.771 2.99,0.771 true 2.031,0.771 2.344,0.927 0.313,0.156 10 false *1 3.031,0.708 3.344,0.865 0.313,0.156 10 false *2
*1 Brake Booster Pump Collar
*2 Brake Booster Pump Bushing


Install the 2 brake booster pump collars and 2 brake booster pump bushings to the brake booster pump assembly as shown in the illustration.

HINT:

Perform this procedure only when replacement of the brake booster pump collars or brake booster pump bushings is necessary.



b.
C378021C02
1.135,0.406 1.396,0.406 true 0.906,3.771 1.24,3.771 false 1.719,0.365 1.99,0.365 true 0.885,4.417 1.219,4.417 false 2.063,3.833 2.25,3.51 2.25,3.51 2.469,3.51 true 1.958,4.167 2.135,4.417 2.135,4.417 2.344,4.417 false 0.979,0.344 1.302,0.5 0.323,0.156 10 false *1 2.021,0.302 2.333,0.458 0.313,0.156 10 false *2 0.75,3.708 1.063,3.865 0.313,0.156 10 false *a 0.729,4.354 1.042,4.51 0.313,0.156 10 false *b 2.385,4.344 2.698,4.5 0.313,0.156 10 false *c 2.51,3.448 2.823,3.604 0.313,0.156 10 false *d
*1 Brake Booster Pump Collar
*2 Brake Booster Pump Bushing
*a Union
*b Connector
*c Wire Harness
*d Stud


Install the brake booster pump assembly, brake booster pump bushing and brake actuator case collar to the brake actuator bracket assembly.

NOTICE:
·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.

·

When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the 2 brake booster pump bushings and 2 brake booster pump collars are installed to the brake booster pump assembly.

·

If installing a new brake booster pump assembly, do not remove the hole plugs before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.




c.

Install the nut.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.
C378018N02
1.844,1.833 2,2.031 0.156,0.198 10 false 1 1.052,1.094 1.177,1.281 0.125,0.188 10 true 2

Engage the claw and clamp to install the brake booster pump assembly wire harness to the brake actuator bracket assembly.

NOTICE:

Engage the claw and clamp in the order shown in the illustration.



Hide 44572C 2.INSTALL NO. 2 BRAKE ACTUATOR HOSE

a.
C378017C02
1.719,1.146 2.073,0.604 2.073,0.604 2.365,0.604 true 2.396,0.531 2.708,0.688 0.313,0.156 10 false *a 2.698,3 3.313,3.198 0.615,0.198 10 false 270°
*a Identification Mark
V100136

Front of the vehicle


Install the No. 2 brake actuator hose to the brake booster pump assembly and slide the clip to secure it.

NOTICE:
·

When connecting the No. 2 brake actuator hose, face the identification mark up.

·

Install the clip within the range shown in the illustration.




Hide 3.INSTALL BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.

Temporarily install the brake actuator with brake booster pump assembly to the vehicle body as shown in the illustration.

C378059C02
5.729,1.75 5.729,1.396 true 5.656,0.958 5.656,0.698 true 5.656,1.76 5.833,1.885 0.177,0.125 10 true *1 5.583,0.948 5.75,1.083 0.167,0.135 10 true *a
*1 Brake Actuator Bracket Assembly - -
*a Cutout - -


NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:

When temporarily installing the brake actuator with brake booster pump assembly, pass the brake actuator bracket assembly through the cutout in the vehicle body.



b.

Return each brake line to its original position.


c.

Install the brake actuator with brake booster pump assembly to the vehicle body with the 2 bolts and nut.

C378034C02
5.906,3.198 5.906,2.635 true 6.448,2.583 6.156,2.583 true 1.292,2.531 1.052,2.531 true 5.5,2.76 5.813,2.917 0.313,0.156 10 false *a 5.792,3.219 6.25,3.417 0.458,0.198 10 false SST 1.292,2.813 1.396,2.979 0.104,0.167 10 true 1 3.573,1.344 3.677,1.51 0.104,0.167 10 true 2 6.219,2.813 6.323,2.979 0.104,0.167 10 true 3 0.885,2.469 1.063,2.604 0.177,0.135 10 true *b 6.469,2.51 6.656,2.646 0.188,0.135 10 true *c
*a Torque Wrench Fulcrum Length *b Bolt (A)
*c Bolt (B) - -


SST
09961-00950  

Torque:
Specified tightening torque : 19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Tighten the 2 bolts and nut in the order shown in the illustration.

·

Make sure to use SST when tightening the bolt (B).



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

Bolt (B): 9.9 N*m (101 kgf*cm, 88 in.*lbf)

·

Tighten the bolt (A) from the bottom of the vehicle.




d.

Remove the protective tape.


e.
C398980

Engage the 5 clamps to install a new No. 2 brake tube clamp to the brake lines.

NOTICE:

Do not kink or damage the brake lines.



f.
C378040

Engage the clamp and install the No. 2 brake tube clamp to the vehicle body.

NOTICE:

Do not kink or damage the brake lines.



g.
C378039

Install the front brake tube way to the vehicle body with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


h.

Engage the clamp to install a new brake tube clamp.


i.

Return the front No. 5 brake tube to its original position.

NOTICE:

Do not apply excessive force to the front No. 5 brake tube.



j.
C378035

Temporarily install the front No. 5 brake tube to the front flexible hose.

NOTICE:
·

Do not kink or damage the front No. 5 brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the front No. 5 brake tube from the connecting parts.




k.
C378009

Engage the clamp to connect the front No. 5 brake tube.

NOTICE:

Do not kink or damage the front No. 5 brake tube.



l.
C378022C03
0.854,1.26 1.26,1.26 true 1.927,1.573 2.333,1.573 true 2.115,1.26 2.521,1.26 true 1.042,0.979 1.448,0.979 true 1.167,0.5 1.396,0.5 1.396,0.5 1.677,1.073 true 2.458,0.667 2.208,0.667 2.208,0.667 1.844,1.146 true 2.344,1.49 2.521,1.646 0.177,0.156 10 true *a 0.677,1.198 0.854,1.344 0.177,0.146 10 true *b 0.854,0.906 1.042,1.063 0.188,0.156 10 true *c 0.969,0.438 1.156,0.583 0.188,0.146 10 true *d 2.469,0.594 2.656,0.75 0.188,0.156 10 true *e 2.542,1.198 2.708,1.344 0.167,0.146 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




m.
C378008C02
2.927,2.906 2.708,2.906 2.708,2.906 2.708,2.646 false 1.802,2.927 2.115,3.083 0.313,0.156 10 false *a 2.958,2.833 3.271,2.99 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




n.
C378036C02
2.865,2.885 2.719,2.885 2.719,2.885 2.719,2.656 false 1.792,2.948 2.104,3.104 0.313,0.156 10 false *a 2.896,2.802 3.208,2.958 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the front No. 5 brake tube while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the front No. 5 brake tube.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




o.
C378006C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




p.

Engage the clamp to install the engine room main wire.


q.
C378024C03
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 473A1 4.CONNECT ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C378004C02
2.896,2.917 2.719,2.917 2.719,2.917 2.719,2.646 false 1.802,2.938 2.115,3.094 0.313,0.156 10 false *a 2.927,2.844 3.125,3.021 0.198,0.177 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the accumulator to brake master cylinder tube to the brake booster pump assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 44572C 5.CONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C378002C02
1.365,0.885 1.542,0.604 1.542,0.604 1.792,0.604 true 1.823,0.531 2.01,0.677 0.188,0.146 10 true *a 1.76,2.177 2.219,2.375 0.458,0.198 10 false 90° 2.667,2.156 3.125,2.354 0.458,0.198 10 false 90°
*a Identification Mark
V100136

Front of the vehicle


Connect the No. 2 brake actuator hose to the No. 1 brake actuator tube and slide the clip to secure it.

NOTICE:
·

When connecting the No. 2 brake actuator hose, face the identification mark up.

·

Install the clip within the range shown in the illustration.




Hide 44551C 7.BLEED NO. 1 BRAKE ACTUATOR TUBE

Hide 8.FILL RESERVOIR WITH BRAKE FLUID

Hide 9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 10.BLEED BRAKE SYSTEM

Hide 53607A 11.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 55708 12.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 13.INSTALL FRONT WHEEL LH