Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › 2018.04–2019.02
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319550 HYBRID VEHICLE TRANSAXLE A

P710 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: The vehicle height changes because of suspension or tire replacement.

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
·

Replacement of engine assembly

·

Replacement of air fuel ratio sensor (sensor 2)

·

Replacement of engine coolant temperature sensor

(w/ Canister Pump Module)

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.*1 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Suspension, tires, etc.*1 Perform headlight ECU sub-assembly LH initialization

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION



PROCEDURE

Hide 1. PERFORM RESOLVER INITIALIZATION

NOTICE:

If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


Hide 2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 45319 5.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 82121 6.DISCONNECT ENGINE WIRE (for LHD)

a.

Remove the 2 bolts.

C388278


b.

Disconnect the 5 clamps.


c.

Disconnect the wire harness connector from the rack and pinion power steering gear assembly.

HINT:

Release the lock before rotating the lock lever.


C374274


d.

Remove the 2 bolts and separate the wire harness from the rack and pinion power steering gear assembly.


Hide 82121 7.DISCONNECT ENGINE WIRE (for RHD)

a.

Remove the 2 bolts.

C379386


b.

Disconnect the 6 clamps.


c.

Disconnect the wire harness connector from the rack and pinion power steering gear assembly.

HINT:

Release the lock before rotating the lock lever.

C387931



Hide 821H2 8.DISCONNECT HV AIR CONDITIONING WIRE

a.
C379387

Remove the bolt.


b.

Disengage the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.


Hide 28193 9.REMOVE STARTER HOLE INSULATOR

a.
C379388

Remove the 2 bolts and starter hole insulator from the engine assembly.


Hide 11363A 10.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C379389

Remove the flywheel housing side cover from the engine assembly.


Hide 51100G 11.REMOVE FRONT FRAME ASSEMBLY

Hide 12361A 12.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
C379390

Remove the bolt and front engine mounting insulator from the front engine mounting bracket.


Hide 12311A 13.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C379391

Remove the 3 bolts and front engine mounting bracket from the hybrid vehicle transaxle assembly.


Hide 12371A 14.REMOVE REAR ENGINE MOUNTING INSULATOR

Hide 12303 15.REMOVE REAR ENGINE MOUNTING BRACKET

a.
C379392

Remove the 4 bolts and rear engine mounting bracket from the hybrid vehicle transaxle assembly.


Hide 30900 16.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C379393

Remove the 8 bolts and hybrid vehicle transaxle assembly from the engine assembly.

NOTICE:
·

To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.

·

To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during hybrid vehicle transaxle assembly removal and installation.




Hide G125A 18.REMOVE MOTOR COOLING COOLER

Hide 33823 19.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C379402

Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.


Hide 44781E 20.REMOVE HOSE BRACKET

a.
C379403

Remove the 2 bolts and hose bracket from the hybrid vehicle transaxle assembly.


Hide 82125 21.REMOVE TRANSMISSION WIRE

a.
C379404

Disconnect the connector.


b.

Remove the bolt and transmission wire from the hybrid vehicle transaxle assembly.


Hide 22.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the 4 bolts and 4 wire harness clamp brackets from the hybrid vehicle transaxle assembly.

C379405


Hide 23.REMOVE TRANSAXLE HOUSING PLUG

a.
C379406

Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.


Hide 24.REMOVE STUD BOLT

a.
C379407

Using a E10 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.