Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2018.08–2019.10
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

When any of the following conditions are met, the skid control ECU (brake booster with master cylinder assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.

Illumination Conditions:
·

Pre-collision brake is operating.*

·

The dynamic radar cruise control system is operating and is applying the brakes.*

·

Secondary collision brake is operating.

·

Brake hold is operating.

·

The parking brake is engaged while the vehicle is being driven.


*: w/ Pre-collision System


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1380 Stop Light Control Relay Malfunction 761
762
·

INF Code: 761

-

When terminal IG1 voltage is 9.5 V or more, stop light drive output (STPO) is on and STP2 is off for 2 seconds or more.


·

INF Code: 762

-

When terminal IG1 voltage is 9.5 V or more, stop light drive output (STPO) is off and the input signals for STP and STP2 differ for 5 seconds or more.



·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake booster with master cylinder assembly)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light set

·

Hybrid vehicle control ECU assembly

·

Certification ECU (smart key ECU assembly)

·

Vehicle approaching speaker controller*


VSC DTC

*: w/ Vehicle Proximity Notification System


WIRING DIAGRAM

C377424E06
3,1.406 3.458,1.604 0.458,0.198 10 false STP 3.344,1.281 3.802,1.479 0.458,0.198 10 false 2 4.688,0.177 5.146,0.375 0.458,0.198 10 false 25 4.938,0.313 5.396,0.51 0.458,0.198 10 false STP1 4.688,1.292 5.146,1.49 0.458,0.198 10 false 15 4.938,1.406 5.396,1.604 0.458,0.198 10 false STP 4.271,0.531 4.729,0.729 0.458,0.198 10 false R8 4.26,0.698 7.125,0.99 2.865,0.292 10 false Certification ECU (Smart Key ECU Assembly) 4.292,1.729 4.75,1.927 0.458,0.198 10 false A28 4.292,1.906 6.76,2.25 2.469,0.344 10 false Hybrid Vehicle Control ECU Assembly 1.979,1.677 2.438,1.875 0.458,0.198 10 false K156 1.969,1.844 3.802,2.26 1.833,0.417 10 false Vehicle Approaching Speaker Controller* 1.125,2.604 2.865,2.865 1.74,0.26 10 false from Auxiliary Battery 0.969,3.677 1.427,3.875 0.458,0.198 10 false STOP 1.573,3.406 2.031,3.604 0.458,0.198 10 false 7 1.75,3.625 2.208,3.823 0.458,0.198 10 false B 1.563,4.969 2.021,5.167 0.458,0.198 10 false 2 1.74,5.198 2.198,5.396 0.458,0.198 10 false GND 3.333,3.073 3.792,3.271 0.458,0.198 10 false 3 3.135,3.292 3.594,3.49 0.458,0.198 10 false L 3.333,3.979 3.792,4.177 0.458,0.198 10 false 4 2.969,4.208 3.427,4.406 0.458,0.198 10 false ACC 3.333,4.958 3.792,5.156 0.458,0.198 10 false 1 2.969,5.188 3.427,5.385 0.458,0.198 10 false OUT 4.677,3.073 5.135,3.271 0.458,0.198 10 false 37 4.906,3.292 5.365,3.49 0.458,0.198 10 false STP2 4.677,3.979 5.135,4.177 0.458,0.198 10 false 22 4.896,4.188 5.354,4.385 0.458,0.198 10 false STPO 4.677,4.958 5.135,5.156 0.458,0.198 10 false 12 4.906,5.188 5.365,5.385 0.458,0.198 10 false STP 4.51,5.854 4.969,6.052 0.458,0.198 10 false A40 4.49,6.042 6.583,6.406 2.094,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.906,6.271 3.365,6.469 0.458,0.198 10 false 2 2.542,6.26 3,6.458 0.458,0.198 10 false STP 1.781,6.271 2.24,6.469 0.458,0.198 10 false E 1.594,6.271 2.052,6.469 0.458,0.198 10 false 4 1.594,7.469 2.052,7.667 0.458,0.198 10 false 4 1.792,7.458 2.25,7.656 0.458,0.198 10 false E 2.573,7.458 3.031,7.656 0.458,0.198 10 false STP 2.917,7.458 3.375,7.656 0.458,0.198 10 false 2 4.979,7.458 5.438,7.656 0.458,0.198 10 false 1 5.177,7.688 5.635,7.885 0.458,0.198 10 false B 6.094,7.688 6.552,7.885 0.458,0.198 10 false E 6.292,7.458 6.75,7.656 0.458,0.198 10 false 2 1.708,5.583 2.167,5.781 0.458,0.198 10 false A37 1.698,5.75 3.542,6.052 1.844,0.302 10 false Stop Light Switch Assembly 0.906,3.396 1.365,3.594 0.458,0.198 10 false 1 1.292,3.396 1.75,3.594 0.458,0.198 10 false 2 1.188,6.833 3.708,7.188 2.521,0.354 10 false Rear Combination Light Assembly LH 5.052,8.167 6.896,8.469 1.844,0.302 10 false Center Stop Light Set 1.177,6.677 1.635,6.875 0.458,0.198 10 false W13 1.167,7.875 1.625,8.073 0.458,0.198 10 false W12 5.063,8 5.521,8.198 0.458,0.198 10 false R47 2.146,6.531 2.76,6.729 0.615,0.198 10 false Stop 2.135,7.74 2.75,7.938 0.615,0.198 10 false Stop 1.167,8.021 3.688,8.375 2.521,0.354 10 false Rear Combination Light Assembly RH 0.427,8.417 3.5,8.844 3.073,0.427 10 false *: w/ Vehicle Proximity Notification System

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STP, STPO AND STP2 TERMINAL)
a.
C373886C24
0.25,0.75 0.667,1 0.417,0.25 2.281,1.604 2.5,0.917 true 2.094,1.875 1.594,0.938 true 2.865,2.885 2.198,2.063 true 0.25,0.25 0.563,0.406 0.313,0.156 10 false *a 0.344,0.781 0.802,0.979 0.458,0.198 10 false A40 2.479,0.75 2.844,0.917 0.365,0.167 10 false STP 1.333,0.76 1.792,0.938 0.458,0.177 10 false STPO 2.792,2.927 3.25,3.104 0.458,0.177 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-12 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A40-12 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V
A40-22 (STPO) - Body ground Always 11 to 14 V
A40-37 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A40-37 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Result Proceed to
All terminal voltages are normal. A
Only STP2 terminal voltage abnormal. B
Only STPO terminal voltage abnormal. C
Only STP terminal voltage abnormal. D
STPO terminal and STP terminal voltage abnormal. E



A

2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

B

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

C

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

D

11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

E

16.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Select the Active Test on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay ON/OFF -
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

OK:

Stop lights turn on/off in accordance with the Active Test.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
3.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Select the Active Test on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay ON/OFF -
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.

According to the display on the GTS, perform the Active Test.


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1380 is output. A
DTC C1380 is not output. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Select the Active Test on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay ON/OFF -
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

b.
E233300C82
1.427,0.271 1.917,0.563 0.49,0.292 1.667,1.146 1.146,1.708 true 0.188,0.115 0.417,0.281 0.229,0.167 10 false *a 1.542,0.333 1.99,0.594 0.448,0.26 10 false A37 0.969,1.708 1.417,1.969 0.448,0.26 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-4 (ACC) - Body ground Active Test is on Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.
C373886C25
0.25,0.75 0.667,1 0.417,0.25 2.865,2.885 2.198,2.063 true 0.25,0.25 0.563,0.406 0.313,0.156 10 false *a 0.344,0.781 0.802,0.979 0.458,0.198 10 false A40 2.792,2.927 3.25,3.104 0.458,0.177 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A28 hybrid vehicle control ECU assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-37 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A40-37 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SMART KEY ECU ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SMART KEY ECU ASSEMBLY)
a.
C373886C25
0.25,0.75 0.667,1 0.417,0.25 2.865,2.885 2.198,2.063 true 0.25,0.25 0.563,0.406 0.313,0.156 10 false *a 0.344,0.781 0.802,0.979 0.458,0.198 10 false A40 2.792,2.927 3.25,3.104 0.458,0.177 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-37 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A40-37 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Result Proceed to
OK A
NG (w/ Vehicle Proximity Notification System) B
NG (w/o Vehicle Proximity Notification System) C



A

REPLACE SMART KEY ECU ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)

C

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)
a.
C373886C40
0.25,0.75 0.667,1 0.417,0.25 2.865,2.885 2.198,2.063 true 0.25,0.25 0.563,0.406 0.313,0.156 10 false *a 0.344,0.781 0.802,0.979 0.458,0.198 10 false A40 2.792,2.927 3.25,3.104 0.458,0.177 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the K156 vehicle approaching speaker controller connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-37 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A40-37 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
C373886C25
0.25,0.75 0.667,1 0.417,0.25 2.865,2.885 2.198,2.063 true 0.25,0.25 0.563,0.406 0.313,0.156 10 false *a 0.344,0.781 0.802,0.979 0.458,0.198 10 false A40 2.792,2.927 3.25,3.104 0.458,0.177 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-37 (STP2) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-37 (STP2) - A37-3 (L) Always Below 1 Ω
A40-37 (STP2) or A37-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-22 (STPO) - A37-4 (ACC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.
C378330C10
0.438,0.698 0.844,0.979 0.406,0.281 2.281,1.615 2.583,0.969 true 2.521,0.792 2.979,0.99 0.458,0.198 10 false STP 0.531,0.75 0.99,0.948 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the W13 rear combination light assembly LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-12 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A40-12 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

NG

12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
a.
C378330C10
0.438,0.698 0.844,0.979 0.406,0.281 2.281,1.615 2.583,0.969 true 2.521,0.792 2.979,0.99 0.458,0.198 10 false STP 0.531,0.75 0.99,0.948 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the W12 rear combination light assembly RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-12 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A40-12 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

NG

13.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT SET)
13.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT SET)
a.
C378330C10
0.438,0.698 0.844,0.979 0.406,0.281 2.281,1.615 2.583,0.969 true 2.521,0.792 2.979,0.99 0.458,0.198 10 false STP 0.531,0.75 0.99,0.948 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the R47 center stop light set connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-12 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A40-12 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

14.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
C378330C10
0.438,0.698 0.844,0.979 0.406,0.281 2.281,1.615 2.583,0.969 true 2.521,0.792 2.979,0.99 0.458,0.198 10 false STP 0.531,0.75 0.99,0.948 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-12 (STP) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-1 (OUT) - A40-12 (STP) Always Below 1 Ω
A37-1 (OUT) or A40-12 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
a.
E360372C13
1.427,0.333 1.927,0.583 0.5,0.25 1.281,1.188 1,1.75 true 2.25,1.188 2.583,1.75 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.552,0.375 2.01,0.531 0.458,0.156 10 false A37 0.844,1.76 1.26,1.958 0.417,0.198 10 false GND 2.552,1.76 2.969,1.958 0.417,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-7 (B) - Body ground Always 11 to 14 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-22 (STPO) or A37-4 (ACC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR