This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speaker ·
Radio and display receiver assembly*1 ·
Stereo component amplifier*2 ·
Telematics transceiver*3 |
*1: for 6 Speakers
*2: for 9 Speakers
*3: w/ Telematics Transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers (w/ Manual (SOS) Switch) | A |
| for 6 Speakers (w/o Manual (SOS) Switch) | B |
| for 9 Speakers (w/ Manual (SOS) Switch) | C |
| for 9 Speakers (w/o Manual (SOS) Switch) | D |
A
B
C
D
Disconnect the K4 radio and display receiver assembly connector.
Disconnect the K157 telematics transceiver connector.
Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
Disconnect the Q8 and P8 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-1 (FR+) or K157-2 (SPI+) - Body ground | Always | 10 kΩ or higher |
| K4-6 (FR-) or K157-3 (SPI-) - Body ground | Always | 10 kΩ or higher |
| K4-2 (FL+) or K8-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K4-7 (FL-) or K8-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K4-4 (RR+) or P8-2 - Body ground | Always | 10 kΩ or higher |
| K4-9 (RR-) or P8-1 - Body ground | Always | 10 kΩ or higher |
| K4-3 (RL+) or Q8-2 - Body ground | Always | 10 kΩ or higher |
| K4-8 (RL-) or Q8-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K157 telematics transceiver connector.
Disconnect the K7 front No. 2 speaker assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K157-5 (SPO+) or K7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K157-6 (SPO-) or K7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SPI+) - 5 (SPO+) | Always | Below 1 Ω |
| 3 (SPI-) - 6 (SPO-) | Always | Below 1 Ω |
| 2 (SPI+) - 3 (SPI-) | Always | 10 kΩ or higher |
| 5 (SPO+) - 6 (SPO-) | Always | 10 kΩ or higher |
| 2 (SPI+) or 5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| 3 (SPI-) or 6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K4 radio and display receiver assembly connector.
Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
Disconnect the Q8 and P8 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-1 (FR+) or K7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K4-6 (FR-) or K7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| K4-2 (FL+) or K8-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K4-7 (FL-) or K8-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K4-4 (RR+) or P8-2 - Body ground | Always | 10 kΩ or higher |
| K4-9 (RR-) or P8-1 - Body ground | Always | 10 kΩ or higher |
| K4-3 (RL+) or Q8-2 - Body ground | Always | 10 kΩ or higher |
| K4-8 (RL-) or Q8-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-2 or K7-3 (+) - Body ground | Always | 10 kΩ or higher |
| N1-1 or K7-1 (-) - Body ground | Always | 10 kΩ or higher |
| O1-2 or K8-3 (+) - Body ground | Always | 10 kΩ or higher |
| O1-1 or K8-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the K157 telematics transceiver connector.
Disconnect the K95 front No. 2 speaker assembly connector.
Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
Disconnect the P1 and Q1 rear speaker assembly connectors.
Disconnect the R1 rear stereo component speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-14 (TWR+) or K157-2 (SPI+) - Body ground | Always | 10 kΩ or higher |
| K14-29 (TWR-) or K157-3 (SPI-) - Body ground | Always | 10 kΩ or higher |
| K14-12 (TWL+) or K95-2 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K14-27 (TWL-) or K95-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K14-15 (FR+) or K109-4 (+TW) - Body ground | Always | 10 kΩ or higher |
| K14-30 (FR-) or K109-2 (-TW) - Body ground | Always | 10 kΩ or higher |
| K14-13 (FL+) or K110-4 (+TW) - Body ground | Always | 10 kΩ or higher |
| K14-28 (FL-) or K110-2 (-TW) - Body ground | Always | 10 kΩ or higher |
| K14-11 (RR+) or P1-1 - Body ground | Always | 10 kΩ or higher |
| K14-26 (RR-) or P1-2 - Body ground | Always | 10 kΩ or higher |
| K14-9 (RL+) or Q1-1 - Body ground | Always | 10 kΩ or higher |
| K14-24 (RL-) or Q1-2 - Body ground | Always | 10 kΩ or higher |
| K14-10 (WF1+) or R1-4 (WF1+) - Body ground | Always | 10 kΩ or higher |
| K14-25 (WF1-) or R1-3 (WF1-) - Body ground | Always | 10 kΩ or higher |
| K14-8 (WF2+) or R1-2 (WF2+) - Body ground | Always | 10 kΩ or higher |
| K14-23 (WF2-) or R1-1 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K157 telematics transceiver connector.
Disconnect the K94 front No. 2 speaker assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K157-5 (SPO+) or K94-2 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K157-6 (SPO-) or K94-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SPI+) - 5 (SPO+) | Always | Below 1 Ω |
| 3 (SPI-) - 6 (SPO-) | Always | Below 1 Ω |
| 2 (SPI+) - 3 (SPI-) | Always | 10 kΩ or higher |
| 5 (SPO+) - 6 (SPO-) | Always | 10 kΩ or higher |
| 2 (SPI+) or 5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| 3 (SPI-) or 6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
Disconnect the P1 and Q1 rear speaker assembly connectors.
Disconnect the R1 rear stereo component speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-15 (FR+) or K109-4 (+TW) - Body ground | Always | 10 kΩ or higher |
| K14-30 (FR-) or K109-2 (-TW) - Body ground | Always | 10 kΩ or higher |
| K14-13 (FL+) or K110-4 (+TW) - Body ground | Always | 10 kΩ or higher |
| K14-28 (FL-) or K110-2 (-TW) - Body ground | Always | 10 kΩ or higher |
| K14-14 (TWR+) or K94-2 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K14-29 (TWR-) or K94-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| K14-12 (TWL+) or K95-2 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K14-27 (TWL-) or K95-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K14-11 (RR+) or P1-1 - Body ground | Always | 10 kΩ or higher |
| K14-26 (RR-) or P1-2 - Body ground | Always | 10 kΩ or higher |
| K14-9 (RL+) or Q1-1 - Body ground | Always | 10 kΩ or higher |
| K14-24 (RL-) or Q1-2 - Body ground | Always | 10 kΩ or higher |
| K14-10 (WF1+) or R1-4 (WF1+) - Body ground | Always | 10 kΩ or higher |
| K14-25 (WF1-) or R1-3 (WF1-) - Body ground | Always | 10 kΩ or higher |
| K14-8 (WF2+) or R1-2 (WF2+) - Body ground | Always | 10 kΩ or higher |
| K14-23 (WF2-) or R1-1 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-2 or K109-3 (+) - Body ground | Always | 10 kΩ or higher |
| N1-1 or K109-1 (-) - Body ground | Always | 10 kΩ or higher |
| O1-2 or K110-3 (+) - Body ground | Always | 10 kΩ or higher |
| O1-1 or K110-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear stereo component speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>REMOVAL
Inspect the rear stereo component speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Inspect the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG