Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE SYSTEM › from 2019.02
RM33C0E _54 Brake _065443 BRAKE SYSTEM (OTHER) _0319346 BRAKE SYSTEM G

BRAKE SYSTEM (OTHER)  BRAKE SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

DTCs may be stored during the inspection procedure. Be sure to clear the DTCs and check that no DTCs are output after the inspection is finished.


PROCEDURE

Hide 1.INSPECT PRESSURE SENSOR (for 2-Pot Caliper)

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge and SST, and connect the GTS.

i.
C416045C01
0.615,0.354 0.792,0.354 false 1.865,0.375 2.042,0.375 false 2.583,0.365 2.76,0.365 false 3.031,3.073 3.031,2.896 false 0.302,3.135 0.406,3.135 0.406,3.135 0.406,3 false 2.083,0.302 2.396,0.458 0.313,0.156 10 false *a 0.823,0.292 1.135,0.448 0.313,0.156 10 false *b 0.146,3.073 0.458,3.229 0.313,0.156 10 false *c 2.427,0.313 2.74,0.469 0.313,0.156 10 false *b 2.958,3.073 3.271,3.229 0.313,0.156 10 false *c
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060)


ii.

Connect the GTS to the DLC3 with the power switch off, the shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.


iv.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



c.

Inspect the reaction force pressure and servo pressure.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Reaction Force Pressure and Servo Pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Reaction Force Pressure
Servo Pressure
50003 105 500,501

ii.

Check the value output from "Reaction Force Pressure" and "Servo Pressure" by depressing the brake pedal.

Standard Result:
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.04 to 0.84 2.85 to 3.45 0.85 to 4.85 MPa (8.7 to 49.5 kgf/cm2, 123 to 703 psi) 0.85 to 4.85 MPa (8.7 to 49.5 kgf/cm2, 123 to 703 psi)
100 N (10 kgf, 22.5 lbf) 0.66 to 1.46 5.24 to 5.84 3.24 to 7.24 MPa (33.0 to 73.8 kgf/cm2, 470 to 1050 psi) 3.24 to 7.24 MPa (33.0 to 73.8 kgf/cm2, 470 to 1050 psi)
150 N (15 kgf, 33.7 lbf) 1.28 to 2.08 7.54 to 8.14 5.54 to 9.54 MPa (56.5 to 97.3 kgf/cm2, 803 to 1383 psi) 5.54 to 9.54 MPa (56.5 to 97.3 kgf/cm2, 803 to 1383 psi)
200 N (20 kgf, 45.0 lbf) 1.90 to 2.70 8.76 to 9.36 6.76 to 10.76 MPa (68.9 to 109.7 kgf/cm2, 980 to 1560 psi) 6.76 to 10.76 MPa (68.9 to 109.7 kgf/cm2, 980 to 1560 psi)


Standard Result:
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.04 to 0.84 2.85 to 3.45 0.85 to 4.85 MPa (8.7 to 49.5 kgf/cm2, 123 to 703 psi) 0.85 to 4.85 MPa (8.7 to 49.5 kgf/cm2, 123 to 703 psi)
100 N (10 kgf, 22.5 lbf) 0.66 to 1.46 5.24 to 5.84 3.24 to 7.24 MPa (33.0 to 73.8 kgf/cm2, 470 to 1050 psi) 3.24 to 7.24 MPa (33.0 to 73.8 kgf/cm2, 470 to 1050 psi)
150 N (15 kgf, 33.7 lbf) 1.28 to 2.08 7.54 to 8.14 5.54 to 9.54 MPa (56.5 to 97.3 kgf/cm2, 803 to 1383 psi) 5.54 to 9.54 MPa (56.5 to 97.3 kgf/cm2, 803 to 1383 psi)
200 N (20 kgf, 45.0 lbf) 1.90 to 2.70 8.76 to 9.36 6.76 to 10.76 MPa (68.9 to 109.7 kgf/cm2, 980 to 1560 psi) 6.76 to 10.76 MPa (68.9 to 109.7 kgf/cm2, 980 to 1560 psi)




d.

Remove the pedal effort gauge and SST.

i.

Remove the pedal effort gauge and SST, and bleed the brake line.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



e.

Inspect the accumulator pressure.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Accumulator Pressure and MT Voltage Value.

Chassis > ABS/VSC/TRC > Data List
Tester Display
MT Voltage Value
Accumulator Pressure
50003 105 279,502

ii.

While fully depressing the brake pedal 4 or 5 times, check that the MT voltage value is 10 V or more once or more.

HINT:

Usually the MT voltage value is 0 V.



iii.

After confirming that the booster pump motor stops, check the accumulator pressure.

Standard Result:

15 to 21 MPa




Hide 2.INSPECT PRESSURE SENSOR (except 2-Pot Caliper)

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge and SST, and connect the GTS.

i.
C376570C03
0.615,0.354 0.792,0.354 false 1.865,0.375 2.042,0.375 false 2.583,0.365 2.76,0.365 false 3.031,3.073 3.031,2.896 false 0.302,3.135 0.406,3.135 0.406,3.135 0.406,3 false 2.083,0.302 2.396,0.458 0.313,0.156 10 false *a 0.823,0.292 1.135,0.448 0.313,0.156 10 false *b 0.146,3.073 0.458,3.229 0.313,0.156 10 false *c 2.427,0.313 2.74,0.469 0.313,0.156 10 false *b 2.958,3.073 3.271,3.229 0.313,0.156 10 false *c
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060)


ii.

Connect the GTS to the DLC3 with the power switch off, the shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.


iv.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



c.

Inspect the reaction force pressure and servo pressure.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Reaction Force Pressure and Servo Pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Reaction Force Pressure
Servo Pressure
50003 105 500,501

ii.

Check the value output from "Reaction Force Pressure" and "Servo Pressure" by depressing the brake pedal.

Standard Result:
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0 to 0.65 2.1 to 6.1 1.8 to 5.8 MPa (18.4 to 59.2 kgf/cm2, 261 to 841 psi) 1.8 to 5.8 MPa (18.4 to 59.2 kgf/cm2, 261 to 841 psi)
100 N (10 kgf, 22.5 lbf) 0.53 to 1.33 4.5 to 8.5 4.2 to 8.2 MPa (42.9 to 83.7 kgf/cm2, 609 to 1189 psi) 4.2 to 8.2 MPa (42.9 to 83.7 kgf/cm2, 609 to 1189 psi)
150 N (15 kgf, 33.7 lbf) 1.16 to 1.96 6.6 to 10.6 6.3 to 10.3 MPa (64.3 to 105.1 kgf/cm2, 914 to 1494 psi) 6.3 to 10.3 MPa (64.3 to 105.1 kgf/cm2, 914 to 1494 psi)
200 N (20 kgf, 45.0 lbf) 1.83 to 2.63 7.1 to 11.1 6.8 to 10.8 MPa (69.4 to 110.2 kgf/cm2, 986 to 1566 psi) 6.8 to 10.8 MPa (69.4 to 110.2 kgf/cm2, 986 to 1566 psi)


Standard Result:
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0 to 0.65 2.08 to 6.08 1.8 to 5.8 MPa (18.4 to 59.2 kgf/cm2, 261 to 841 psi) 1.8 to 5.8 MPa (18.4 to 59.2 kgf/cm2, 261 to 841 psi)
100 N (10 kgf, 22.5 lbf) 0.53 to 1.33 4.48 to 8.48 4.2 to 8.2 MPa (42.9 to 83.7 kgf/cm2, 609 to 1189 psi) 4.2 to 8.2 MPa (42.9 to 83.7 kgf/cm2, 609 to 1189 psi)
150 N (15 kgf, 33.7 lbf) 1.16 to 1.96 6.58 to 10.58 6.3 to 10.3 MPa (64.3 to 105.1 kgf/cm2, 914 to 1494 psi) 6.3 to 10.3 MPa (64.3 to 105.1 kgf/cm2, 914 to 1494 psi)
200 N (20 kgf, 45.0 lbf) 1.83 to 2.63 7.1 to 11.1 6.8 to 10.8 MPa (69.4 to 110.2 kgf/cm2, 986 to 1566 psi) 6.8 to 10.8 MPa (69.4 to 110.2 kgf/cm2, 986 to 1566 psi)




d.

Remove the pedal effort gauge and SST.

i.

Remove the pedal effort gauge and SST, and bleed the brake line.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



e.

Inspect the accumulator pressure.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Accumulator Pressure and MT Voltage Value.

Chassis > ABS/VSC/TRC > Data List
Tester Display
MT Voltage Value
Accumulator Pressure
50003 105 279,502

ii.

While fully depressing the brake pedal 4 or 5 times, check that the MT voltage value is 10 V or more once or more.

HINT:

Usually the MT voltage value is 0 V.



iii.

After confirming that the booster pump motor stops, check the accumulator pressure.

Standard Result:

15 to 21 MPa




Hide 47210L 3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for 2-Pot Caliper)

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge and SST, and connect the GTS.

i.
C416045C01
0.615,0.354 0.792,0.354 false 1.865,0.375 2.042,0.375 false 2.583,0.365 2.76,0.365 false 3.031,3.073 3.031,2.896 false 0.302,3.135 0.406,3.135 0.406,3.135 0.406,3 false 2.083,0.302 2.396,0.458 0.313,0.156 10 false *a 0.823,0.292 1.135,0.448 0.313,0.156 10 false *b 0.146,3.073 0.458,3.229 0.313,0.156 10 false *c 2.427,0.313 2.74,0.469 0.313,0.156 10 false *b 2.958,3.073 3.271,3.229 0.313,0.156 10 false *c
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060)


ii.

Connect the GTS to the DLC3 with the power switch off, the shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.



v.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



c.

Check operation without the brake booster.

i.

Inspect and adjust the brake pedal height.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT


ii.
C376571C03
1.313,1.281 1.313,1.604 1.313,1.604 1.656,1.604 true 0.76,1.625 1.083,1.625 1.083,1.625 1.083,1.406 true 1.656,1.521 1.833,1.698 0.177,0.177 10 true *a 0.583,1.552 0.76,1.719 0.177,0.167 10 true *b
*a Fluid Level Support Line
*b MIN Line


Adjust the brake fluid level of the reservoir so that it is between the MIN line and fluid level support line.


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

iv.

Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


v.

Perform "Motor Invalid" according to the display on the GTS.


vi.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



vii.

Check that the brake pedal is firm.


viii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 105 11,12

ix.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Result:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.69 to 2.39 2.61 to 3.31 0.02 to 2.02 MPa (0.2 to 20.6 kgf/cm2, 3 to 293 psi) 0.02 to 2.02 MPa (0.2 to 20.6 kgf/cm2, 3 to 293 psi)
500 N (51 kgf, 112.4 lbf) 1.97 to 2.67 2.33 to 3.03 2.05 to 4.05 MPa (20.9 to 41.3 kgf/cm2, 297 to 587 psi) 2.05 to 4.05 MPa (20.9 to 41.3 kgf/cm2, 297 to 587 psi)


Standard Result:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.69 to 2.39 2.61 to 3.31 0.02 to 2.02 MPa (0.2 to 20.6 kgf/cm2, 3 to 293 psi) 0.02 to 2.02 MPa (0.2 to 20.6 kgf/cm2, 3 to 293 psi)
500 N (51 kgf, 112.4 lbf) 1.97 to 2.67 2.33 to 3.03 2.05 to 4.05 MPa (20.9 to 41.3 kgf/cm2, 297 to 587 psi) 2.05 to 4.05 MPa (20.9 to 41.3 kgf/cm2, 297 to 587 psi)



x.

Remove the pedal effort gauge and SST, and bleed the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


xi.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Accumulator Pressure, and check the output pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Pressure
50003 105 502
Standard Result:

15 to 21 MPa





Hide 47210L 4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (except 2-Pot Caliper)

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge and SST, and connect the GTS.

i.
C376570C02
0.615,0.354 0.792,0.354 false 1.865,0.375 2.042,0.375 false 2.583,0.365 2.76,0.365 false 3.031,3.073 3.031,2.896 false 0.302,3.135 0.406,3.135 0.406,3.135 0.406,3 false 2.063,0.302 2.375,0.458 0.313,0.156 10 false *a 0.823,0.271 1.135,0.427 0.313,0.156 10 false *b 0.156,3.063 0.469,3.219 0.313,0.156 10 false *c 2.438,0.292 2.75,0.448 0.313,0.156 10 false *b 2.958,3.073 3.271,3.229 0.313,0.156 10 false *c
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060)


ii.

Connect the GTS to the DLC3 with the power switch off, the shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.



v.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



c.

Check operation without the brake booster.

i.

Inspect and adjust the brake pedal height.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT


ii.
C376571C03
1.313,1.281 1.313,1.604 1.313,1.604 1.656,1.604 true 0.76,1.625 1.083,1.625 1.083,1.625 1.083,1.406 true 1.656,1.521 1.833,1.698 0.177,0.177 10 true *a 0.583,1.552 0.76,1.719 0.177,0.167 10 true *b
*a Fluid Level Support Line
*b MIN Line


Adjust the brake fluid level of the reservoir so that it is between the MIN line and fluid level support line.


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

iv.

Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


v.

Perform "Motor Invalid" according to the display on the GTS.


vi.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



vii.

Check that the brake pedal is firm.


viii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 105 11,12

ix.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Result:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.52 to 2.22 2.78 to 3.48 0.04 to 2.04 MPa (0.4 to 20.8 kgf/cm2, 6 to 296 psi) 0.04 to 2.04 MPa (0.4 to 20.8 kgf/cm2, 6 to 296 psi)
500 N (51 kgf, 112.4 lbf) 1.81 to 2.51 2.49 to 3.19 2.06 to 4.06 MPa (21.0 to 41.4 kgf/cm2, 299 to 589 psi) 2.06 to 4.06 MPa (21.0 to 41.4 kgf/cm2, 299 to 589 psi)


Standard Result:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.52 to 2.22 2.78 to 3.48 0.04 to 2.04 MPa (0.4 to 20.8 kgf/cm2, 6 to 296 psi) 0.04 to 2.04 MPa (0.4 to 20.8 kgf/cm2, 6 to 296 psi)
500 N (51 kgf, 112.4 lbf) 1.81 to 2.51 2.49 to 3.19 2.06 to 4.06 MPa (21.0 to 41.4 kgf/cm2, 299 to 589 psi) 2.06 to 4.06 MPa (21.0 to 41.4 kgf/cm2, 299 to 589 psi)



x.

Remove the pedal effort gauge and SST, and bleed the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


xi.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Accumulator Pressure, and check the output pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Pressure
50003 105 502
Standard Result:

15 to 21 MPa





Hide 5.INSPECT STROKE SIMULATOR (for 2-Pot Caliper)

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Connect the GTS and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the GTS to the DLC3 with the power switch off, the shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.




c.

Check operation with the brake booster.

i.

Turn the power switch on (IG).


ii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 105 11,12

iii.

Depress the brake pedal 4 or 5 times.


iv.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
50 N (5 kgf, 11.2 lbf) 1.35 to 2.05 2.95 to 3.65
100 N (10 kgf, 22.5 lbf) 1.54 to 2.24 2.76 to 3.46
150 N (15 kgf, 33.7 lbf) 1.68 to 2.38 2.62 to 3.32




Hide 6.INSPECT STROKE SIMULATOR (except 2-Pot Caliper)

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Connect the GTS and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the GTS to the DLC3 with the power switch off, the shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.




c.

Check operation with the brake booster.

i.

Turn the power switch on (IG).


ii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 105 11,12

iii.

Depress the brake pedal 4 or 5 times.


iv.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
50 N (5 kgf, 11.2 lbf) 1.38 to 2.08 2.92 to 3.62
100 N (10 kgf, 22.5 lbf) 1.58 to 2.28 2.72 to 3.42
150 N (15 kgf, 33.7 lbf) 1.71 to 2.41 2.59 to 3.29