Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2019.02
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter assembly receives vehicle speed signals from the skid control ECU (brake booster with master cylinder assembly) via CAN communication. The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake booster with master cylinder assembly). The skid control ECU (brake booster with master cylinder assembly) supplies power to the vehicle speed sensor. The skid control ECU (brake booster with master cylinder assembly) detects vehicle speed signals based on pulses of the voltage.

HINT:

Factors that affect the indicated vehicle speed include the tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error.


WIRING DIAGRAM

E277735E27
0.073,3.063 2.146,3.573 2.073,0.51 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.969,3.167 6.333,3.365 3.365,0.198 10 false : CAN Communication Line 5.281,3.115 7.094,3.302 1.813,0.188 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before starting the following inspection, inspect the speedometer and check that the tire size and air pressure are as specified.

Tire size and air pressure: Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION

Speedometer: Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

B

2.CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Check if electronically controlled brake system DTCs are output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.PERFORM ACTIVE TEST USING GTS

B

3.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speedometer Operation (0km/h,0MPH) Speedometer 0km/h (0mph) ON -
Speedometer Operation (40km/h,40MPH) Speedometer 40 km/h (40 mph) ON The value displayed on the speedometer may deviate.
Reference km/h*1:
40 → 41.1 to 45.2
Reference km/h*2:
40 → 41.7 to 46.2
Reference mph*3:
40 → 42 to 44.5
Speedometer Operation (80km/h,80MPH) Speedometer 80 km/h (80 mph) ON The value displayed on the speedometer may deviate.
Reference km/h*1:
80 → 82.2 to 86.3
Reference km/h*2:
80 → 83.4 to 88.4
Reference mph*3:
80 → 83.1 to 87.1
Speedometer Operation (120km/h,120MPH) Speedometer 120 km/h (120 mph) ON The value displayed on the speedometer may deviate.
Reference km/h*1:
120 → 123.3 to 127.4
Reference km/h*2:
120 → 125.1 to 130.6
Reference mph*3:
120 → 124.7 to 129.6
Speedometer Operation (160km/h,160MPH) Speedometer 160 km/h (160 mph) ON The value displayed on the speedometer may deviate.
Reference km/h*1:
160 → 164.4 to 168.5
Reference km/h*2:
160 → 166.2 to 173.2
Speedometer Operation (200km/h,200MPH) Speedometer 200 km/h (200 mph) ON The value displayed on the speedometer may deviate.
Reference km/h*1:
200 → 205.6 to 209.7
Reference km/h*2:
200 → 207.7 to 215.7
Speedometer Operation (240km/h,240MPH) Speedometer 240 km/h (240 mph) ON The value displayed on the speedometer may deviate.
Reference km/h*1:
240 → 246.7 to 250.8
Reference km/h*2:
240 → 249.2 to 258.0

*1: for Speedometer with Metric Units for Main Scale (RHD without Front Fog Light)

*2: for Speedometer with Metric Units for Main Scale (LHD, RHD with Front Fog Light)

*3: for Speedometer with Imperial Units for Main Scale


Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (0km/h,0MPH)
50004 409 199
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (40km/h,40MPH)
50004 409 200
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (80km/h,80MPH)
50004 409 201
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (120km/h,120MPH)
50004 409 202
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (160km/h,160MPH)
50004 409 203
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (200km/h,200MPH)
50004 409 204
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (240km/h,240MPH)
50004 409 205
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPLACE COMBINATION METER ASSEMBLY