Home › Vehicle Interior › METER / GAUGE / DISPLAY › COMBINATION METER › 2019.02–2021.02
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330019 COMBINATION METER A

METER / GAUGE / DISPLAY  COMBINATION METER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Parking Support Brake System*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55435B 5.REMOVE NO. 1 METER HOOD CLUSTER

Hide 55436B 6.REMOVE NO. 2 METER HOOD CLUSTER

Hide 55410C 7.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.

for Manual Tilt and Manual Telescopic Steering Column:

i.

Release the tilt and telescopic lever and fully extend and lower the steering column assembly.


ii.

Lock the tilt and telescopic lever.



b.
E372322C02
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area shown in the illustration.


c.
E365357C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area shown in the illustration.


d.
E372323C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 4 clips to separate the instrument cluster finish panel assembly.


e.
E372324

Remove the 2 clips.


f.
E372325C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration.


g.
E371529C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration.


h.
E371530C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides as shown in the illustration.


i.

Disconnect the connector to remove the instrument cluster finish panel assembly.


Hide 83100 8.REMOVE COMBINATION METER ASSEMBLY

a.
E372312

Remove the 3 screws.


b.
E372313C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration.


c.

Disengage the clamp.


d.

Disconnect each connector to remove the combination meter assembly.