Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › 2019.02–2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0387691 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  U0233  Lost Communication with Blind Spot Monitor Master Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH judges that there is a communication problem with the blind spot monitor sensor RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0232 Lost Communication with Blind Spot Monitor Slave Module The clearance warning ECU assembly cannot receive signals from the blind spot monitor sensor (slave)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 5 junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor RH


U0233 Lost Communication with Blind Spot Monitor Master Module The clearance warning ECU assembly cannot receive signals from the blind spot monitor sensor (master)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 5 junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor RH

·

Power source circuit of blind spot monitor sensor RH

·

Blind spot monitor sensor RH ground circuit

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E334320E21
5.635,3.438 5.49,3.438 5.49,3.438 4.917,2.354 false 2.49,2.594 3.656,3.146 1.167,0.552 10 false Blind Spot Monitor Sensor LH 3.49,4.156 5.667,4.563 2.177,0.406 10 false Clearance Warning ECU Assembly 5.698,3.531 6.615,4.104 0.917,0.573 10 false No. 5 Junction Connector 3.135,0.948 4.177,1.49 1.042,0.542 10 false CA2P 4.552,3.292 5.594,3.833 1.042,0.542 10 false CANL 3.125,1.792 4.167,2.333 1.042,0.542 10 false CA2N 4.115,3.281 5.156,3.823 1.042,0.542 10 false CANH 5.563,0.938 6.125,1.198 0.563,0.26 10 false CA2P 5.552,1.813 6.594,2.354 1.042,0.542 10 false CA2N 2.542,1.927 3.583,2.469 1.042,0.542 10 false BLGD 6.135,1.969 6.625,2.177 0.49,0.208 10 false BRGD 6.24,1.24 6.729,1.448 0.49,0.208 10 false BRB 2.51,1.25 3,1.458 0.49,0.208 10 false BLB 5.385,0.938 5.531,1.115 0.146,0.177 10 false 1 3.594,0.938 3.74,1.115 0.146,0.177 10 false 1 3.583,1.563 3.729,1.74 0.146,0.177 10 false 6 5.385,1.573 5.531,1.75 0.146,0.177 10 false 6 2.49,2.427 2.833,2.646 0.344,0.219 10 false W6 6.615,1.865 6.958,2.115 0.344,0.25 10 false 10 2.365,1.135 2.51,1.313 0.146,0.177 10 false 5 6.615,1.104 6.76,1.281 0.146,0.177 10 false 5 5.552,2.438 5.802,2.625 0.25,0.188 10 false W5 3.5,3.99 3.865,4.177 0.365,0.188 10 false R39 4.688,3.063 4.969,3.24 0.281,0.177 10 false 38 4.208,3.063 4.469,3.219 0.26,0.156 10 false 37 5.698,3.354 6.146,3.573 0.448,0.219 10 false R100 4.01,0.938 4.156,1.115 0.146,0.177 10 false 3 4.969,0.938 5.188,1.135 0.219,0.198 10 false 2 4.26,2.427 4.406,2.604 0.146,0.177 10 false 1 4.958,1.573 5.25,1.802 0.292,0.229 10 false 13 4.677,2.438 5,2.677 0.323,0.24 10 false 12 3.938,1.563 4.208,1.781 0.271,0.219 10 false 14 2.313,1.823 2.656,2.052 0.344,0.229 10 false 10 1.271,0.625 2.313,1.167 1.042,0.542 10 false ECU-IG1 NO. 4 0.125,0.49 1.167,1.031 1.042,0.542 10 false from IG1-NO. 1 Relay 5.542,2.604 6.719,3.365 1.177,0.76 10 false Blind Spot Monitor Sensor RH

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK DTC
a.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC U0232 is only output A
DTC U0233 is only output B
DTC U0232 and U0233 are output C



A

2.CHECK CAN BUS MAIN WIRE

B

5.CHECK CAN BUS MAIN WIRE

C

8.CHECK CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH)
2.CHECK CAN BUS MAIN WIRE
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the W6 blind spot monitor sensor LH connector.


c.
E359601C05
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.594,0.25 2.052,0.448 0.458,0.198 10 false W6 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) -W6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - No. 5 JUNCTION CONNECTOR)

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH POWER SOURCE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - No. 5 JUNCTION CONNECTOR)

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH POWER SOURCE)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CAN BUS MAIN WIRE
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the W5 blind spot monitor sensor RH connector.


c.
E359601C06
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.583,0.25 2.042,0.448 0.458,0.198 10 false W5 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) -W5-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - No. 5 JUNCTION CONNECTOR)

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)

OK

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH POWER SOURCE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - No. 5 JUNCTION CONNECTOR)

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH POWER SOURCE)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH)
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
E334331C22
1.542,2.865 1.906,3.125 0.365,0.26 0.229,1.448 0.635,1.719 0.406,0.271 0.99,3.021 1.177,3.021 1.177,3.021 1.615,3.448 false 2.365,3.99 2.49,4.302 2.49,4.302 2.635,4.302 false 2.385,1.875 2.542,2.49 2.542,2.49 2.688,2.49 false 2.406,1.583 2.646,0.917 2.646,0.917 2.792,0.917 false 0.24,2.708 0.552,2.865 0.313,0.156 10 false *1 0.167,0.115 0.479,0.271 0.313,0.156 10 false *a 1.563,2.917 1.875,3.115 0.313,0.198 10 false K154 0.271,1.5 0.656,1.698 0.385,0.198 10 false R100 2.844,0.844 3.427,1.052 0.583,0.208 10 false CANH 2.75,2.417 3.333,2.625 0.583,0.208 10 false CANL 2.708,4.229 3.292,4.438 0.583,0.208 10 false BAT 0.729,2.927 1.313,3.135 0.583,0.208 10 false CG
*1 DLC3
*a Component with harness connected
(No. 5 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
R100-1 (CANH) -R100-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
R100-1(CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
R100-12(CANL) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
R100-1(CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
R100-12(CANL) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

9.CONFIRM CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)

B

11.CHECK FOR OPEN IN CAN BUS WIRE (No. 5 JUNCTION CONNECTOR)

C

15.CHECK FOR SHORT IN CAN BUS WIRES (No. 5 JUNCTION CONNECTOR)

D

19.CHECK FOR SHORT IN CAN BUS WIRES (No. 5 JUNCTION CONNECTOR)
9.CONFIRM CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the R39 clearance warning ECU assembly connector.


b.
C285240C84
1.49,0.302 1.917,0.542 0.427,0.24 2.563,1.177 2.313,1.813 2.313,1.813 2.146,1.813 true 2.677,1.188 2.76,1.885 2.76,1.885 2.906,1.885 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.594,0.323 2.208,0.521 0.615,0.198 10 false R39 1.781,1.76 2.24,2.021 0.458,0.26 10 false CANH 2.969,1.813 3.427,2.073 0.458,0.26 10 false CANL
*a Front view of wire harness connector
(to clearance warning ECU assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-37(CANH) - R39-38(CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

10.CHECK DTC

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - No. 5 JUNCTION CONNECTOR)

10.CHECK DTC
a.

Clear the DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs
50002 170

b.

Check for DTCs.

Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
50001 170

Result:
Result Proceed to
DTC U0232 and U0233 are output A
DTC U0232 and U0233 are not output B



A

B

11.CHECK FOR OPEN IN CAN BUS WIRE (No. 5 JUNCTION CONNECTOR)
a.
E331799C47
1.448,0.25 1.865,0.49 0.417,0.24 0.917,2.188 1.115,2.99 1.115,2.99 1.292,2.99 false 1.115,1.875 1.26,0.938 1.26,0.938 1.438,0.938 false 1.135,2.167 1.333,2.802 1.333,2.802 1.51,2.802 false 0.906,1.813 1.083,0.656 1.083,0.656 1.198,0.656 false 0.708,1.823 0.688,0.375 0.688,0.375 0.802,0.375 false 0.698,2.156 0.896,3.26 0.896,3.26 1.073,3.26 false 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.49,0.292 1.948,0.49 0.458,0.198 10 false R100 1.26,0.573 1.875,0.771 0.615,0.198 10 false CANH*b 1.49,0.833 2.104,1.031 0.615,0.198 10 false CANH*c 1.344,2.906 1.958,3.104 0.615,0.198 10 false CANL*b 1.604,2.698 2.219,2.896 0.615,0.198 10 false CANL*c 0.844,0.281 1.458,0.479 0.615,0.198 10 false CANH*d 1.115,3.188 1.729,3.385 0.615,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to blind spot monitor sensor RH CAN main wire
*c to blind spot monitor sensor LH CAN main wire
*d to clearance warning ECU assembly CAN wire


Disconnect the R100 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-3 (CANH) - R100-14(CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
R100-2 (CANH) - R100-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
R100-1 (CANH) - R100-12(CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH CAN main wire) B
NG (to blind spot monitor sensor LH CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE No. 5 JUNCTION CONNECTOR

B

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH)

C

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH)

D

14.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH)
a.

Reconnect the R100 No. 5 junction connector.


b.
E359601C06
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.583,0.25 2.042,0.448 0.458,0.198 10 false W5 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor RH)


Disconnect the W5 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - No. 5 JUNCTION CONNECTOR)

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH)
a.

Reconnect the R100 No. 5 junction connector.


b.
E359601C05
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.594,0.25 2.052,0.448 0.458,0.198 10 false W6 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor LH)


Disconnect the W6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) -W6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - No. 5 JUNCTION CONNECTOR)

14.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the R100 No. 5 junction connector.


b.
C285240C84
1.49,0.302 1.917,0.542 0.427,0.24 2.563,1.177 2.313,1.813 2.313,1.813 2.146,1.813 true 2.677,1.188 2.76,1.885 2.76,1.885 2.906,1.885 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.594,0.323 2.208,0.521 0.615,0.198 10 false R39 1.781,1.76 2.24,2.021 0.458,0.26 10 false CANH 2.969,1.813 3.427,2.073 0.458,0.26 10 false CANL
*a Front view of wire harness connector
(to clearance warning ECU assembly)


Disconnect the R39 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-37(CANH) - R39-38(CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - No. 5 JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (No. 5 JUNCTION CONNECTOR)
a.
E331799C48
1.448,0.25 1.865,0.49 0.417,0.24 0.917,2.188 1.115,2.99 1.115,2.99 1.292,2.99 false 1.115,1.875 1.26,0.938 1.26,0.938 1.438,0.938 false 1.135,2.167 1.333,2.802 1.333,2.802 1.51,2.802 false 0.906,1.813 1.083,0.656 1.083,0.656 1.198,0.656 false 0.708,1.823 0.688,0.375 0.688,0.375 0.802,0.375 false 0.698,2.156 0.896,3.26 0.896,3.26 1.073,3.26 false 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.49,0.292 1.948,0.49 0.458,0.198 10 false R100 1.26,0.573 1.875,0.771 0.615,0.198 10 false CANH*b 1.49,0.833 2.104,1.031 0.615,0.198 10 false CANH*c 1.344,2.906 1.958,3.104 0.615,0.198 10 false CANL*b 1.604,2.698 2.219,2.896 0.615,0.198 10 false CANL*c 0.844,0.281 1.458,0.479 0.615,0.198 10 false CANH*d 1.115,3.188 1.729,3.385 0.615,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to blind spot monitor sensor RH CAN main wire
*c to blind spot monitor sensor LH CAN main wire
*d to clearance warning ECU assembly CAN wire


Disconnect the R100 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-3 (CANH) - R100-14(CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
R100-2 (CANH) - R100-13(CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
R100-1 (CANH) - R100-12(CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH CAN main wire) B
NG (to blind spot monitor sensor LH CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE No. 5 JUNCTION CONNECTOR

B

16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)

C

17.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)

D

18.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
a.

Reconnect the R100 No. 5 junction connector.


b.
E359601C06
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.583,0.25 2.042,0.448 0.458,0.198 10 false W5 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor RH)


Disconnect the W5 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - No. 5 JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.

Reconnect the R100 No. 5 junction connector.


b.
E359601C05
1.5,0.208 1.885,0.438 0.385,0.229 0.76,1.688 0.906,1.688 0.906,1.688 1.427,1.073 false 1.865,1.958 1.698,1.958 1.698,1.958 1.438,1.219 false 1.594,0.25 2.052,0.448 0.458,0.198 10 false W6 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to blind spot monitor sensor LH)


Disconnect the W6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) -W6-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - No. 5 JUNCTION CONNECTOR)

18.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the R100 No. 5 junction connector.


b.
C285240C84
1.49,0.302 1.917,0.542 0.427,0.24 2.563,1.177 2.313,1.813 2.313,1.813 2.146,1.813 true 2.677,1.188 2.76,1.885 2.76,1.885 2.906,1.885 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.594,0.323 2.208,0.521 0.615,0.198 10 false R39 1.781,1.76 2.24,2.021 0.458,0.26 10 false CANH 2.969,1.813 3.427,2.073 0.458,0.26 10 false CANL
*a Front view of wire harness connector
(to clearance warning ECU assembly)


Disconnect the R39 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-37(CANH) - R39-38(CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - No. 5 JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (No. 5 JUNCTION CONNECTOR)
a.

Disconnect the R100 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

E348217C12
1.99,0.49 2.438,0.75 0.448,0.26 5.479,0.479 5.927,0.74 0.448,0.26 5.792,1.26 6.135,0.844 6.135,0.844 6.323,0.844 true 6.49,1.792 6.406,2.385 6.406,2.385 6.594,2.385 true 1.75,1.74 2.115,2.219 2.115,2.219 2.302,2.219 true 1.583,1.719 2.031,2.438 2.031,2.438 2.219,2.438 true 1.729,1.5 1.333,0.354 1.333,0.354 1.125,0.354 true 1.552,1.51 1.271,0.667 1.271,0.667 1.063,0.667 true 1.396,1.521 1.156,1 1.156,1 0.948,1 true 1.448,1.719 1.198,2.208 1.198,2.208 0.99,2.208 true 4.344,0.323 4.656,0.479 0.313,0.156 10 false *1 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 0.563,0.292 1.229,0.531 0.667,0.24 10 false CANH*c 0.375,0.917 0.938,1.177 0.563,0.26 10 false CANH*d 0.49,0.573 1.125,0.813 0.635,0.24 10 false CANH*b 2.063,0.542 2.521,0.74 0.458,0.198 10 false R100 5.552,0.531 6.083,0.74 0.531,0.208 10 false K154 6.656,2.333 7.083,2.552 0.427,0.219 10 false BAT 6.375,0.771 6.646,0.979 0.271,0.208 10 false CG 2.385,2.135 3.052,2.375 0.667,0.24 10 false CANL*c 0.438,2.125 1,2.385 0.563,0.26 10 false CANL*d 2.271,2.354 2.906,2.594 0.635,0.24 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to blind spot monitor sensor RH CAN main wire
*c to blind spot monitor sensor LH CAN main wire *d to clearance warning ECU assembly CAN wire


Standard Resistance:
Tester Connection Condition Specified Condition
R100-3 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R100-14 (CANL) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R100-3 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R100-14 (CANL) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R100-1 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R100-12 (CANL) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R100-1 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R100-12 (CANL) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R100-2 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R100-13 (CANL) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R100-2 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R100-13 (CANL) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor RH CAN main wire) B
NG (to blind spot monitor sensor LH CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE No. 5 JUNCTION CONNECTOR

B

20.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)

C

21.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)

D

22.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
20.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH)
a.

Reconnect the R100 No. 5 junction connector.


b.

Disconnect the W5 blind spot monitor sensor RH connector.


c.
E334330C81
1.479,1.813 1.875,2.104 0.396,0.292 1.396,0.198 1.792,0.49 0.396,0.292 0.729,0.771 0.917,0.771 0.917,0.771 1.385,1.021 false 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 false 1.125,1.948 1.313,1.948 1.313,1.948 1.625,2.354 false 2.271,2.823 2.458,3.042 2.458,3.042 2.573,3.042 false 0.313,1.813 0.625,1.969 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.521,1.875 1.833,2.073 0.313,0.198 10 false K154 1.5,0.26 1.813,0.458 0.313,0.198 10 false W5 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.656,2.948 3.271,3.146 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to blind spot monitor sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W5-6 (CA2N) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W5-1 (CA2P) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
W5-6 (CA2N) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH - No. 5 JUNCTION CONNECTOR)

21.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH)
a.

Reconnect the R100 No. 5 junction connector.


b.

Disconnect the W6 blind spot monitor sensor LH connector.


c.
E334330C82
1.479,1.813 1.875,2.104 0.396,0.292 1.396,0.198 1.792,0.49 0.396,0.292 0.729,0.771 0.917,0.771 0.917,0.771 1.385,1.021 false 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 false 1.125,1.948 1.313,1.948 1.313,1.948 1.625,2.354 false 2.271,2.823 2.458,3.042 2.458,3.042 2.573,3.042 false 0.292,1.823 0.604,1.979 0.313,0.156 10 false *1 0.229,0.208 0.542,0.365 0.313,0.156 10 false *a 1.521,1.875 1.833,2.073 0.313,0.198 10 false K154 1.5,0.26 1.813,0.458 0.313,0.198 10 false W6 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.656,2.948 3.271,3.146 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to blind spot monitor sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W6-6 (CA2N) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
W6-1 (CA2P) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
W6-6 (CA2N) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH - No. 5 JUNCTION CONNECTOR)

22.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the R100 No. 5 junction connector.


b.
E348218C10
1.406,0.302 1.771,0.563 0.365,0.26 1.542,1.74 1.906,2 0.365,0.26 2.958,1.865 2.76,1.865 2.76,1.865 2.594,1.271 false 2.604,3.25 2.406,3.25 2.406,3.25 2.25,2.833 false 1.625,2.49 1.302,3.281 1.302,3.281 1.083,3.281 false 2.938,2.219 2.74,2.219 2.74,2.219 2.49,1.281 false 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.198,2.031 0.51,2.229 0.313,0.198 10 false *1 1.479,0.344 1.792,0.5 0.313,0.156 10 false R39 1.563,1.792 2.021,1.99 0.458,0.198 10 false K154 2.99,1.771 3.396,2 0.406,0.229 10 false CANL 2.979,2.156 3.385,2.385 0.406,0.229 10 false CANH 2.635,3.167 3.042,3.396 0.406,0.229 10 false BAT 0.865,3.198 1.271,3.427 0.406,0.229 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to clearance warning ECU assembly)


Disconnect the R39 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-37 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R39-38 (CANL) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R39-37 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R39-38 (CANL) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - No. 5 JUNCTION CONNECTOR)