The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
1. PRECAUTION
Make sure to select face mode before disconnecting the cable from the negative (-) auxiliary battery terminal.
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
53607A
4.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
for LHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
87246
5.DISCONNECT OUTLET HEATER WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose.
Do not apply excessive force to the outlet heater water hose.
Prepare a drain pan or cloth in case the coolant leaks.
87245
6.DISCONNECT INLET HEATER WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose.
Do not apply excessive force to the inlet heater water hose.
Prepare a drain pan or cloth in case the coolant leaks.
88707
7.DISCONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the bolt and rotate the hook connector as shown in the illustration.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710E
8.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Disconnect the air conditioning tube and accessory assembly.
Remove the O-ring from the air conditioning tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
9.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
10.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
11.REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY
45250
12.REMOVE STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
for Power Tilt and Power Telescopic Steering Column:
13.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
89343C
14.REMOVE NO. 1 CLEARANCE WARNING BUZZER (for LHD)
82877
15.REMOVE ECU INTEGRATION BOX RH (for LHD)
89980
16.REMOVE HYBRID VEHICLE CONTROL ECU ASSEMBLY (for RHD)
17.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)
86740
18.REMOVE TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)
88625Q
19.REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR
Disconnect the connector and aspirator to remove the cooler (room temp. sensor) thermistor.
78118
20.REMOVE ACCELERATOR PEDAL PAD
78111
21.REMOVE ACCELERATOR PEDAL
58569D
22.REMOVE FRONT FLOOR CAUTION PLATE COVER
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claw as shown by the arrow (1), and then pull the front floor caution plate cover as shown by the arrow (2) in the illustration to disengage the guide and remove it.
87212F
23.REMOVE REAR NO. 2 AIR DUCT
for LHD:
Remove the front floor carpet clip.
Remove the front floor carpet clip.
Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.
|
Remove in this Direction |
Disengage the 4 claws and remove the rear No. 2 air duct as shown in the illustration.
87212
24.REMOVE REAR NO. 1 AIR DUCT
Disengage the 2 claws and remove the rear No. 1 air duct.
87212H
25.REMOVE REAR NO. 4 AIR DUCT
Remove the front floor carpet clip.
Remove the front floor carpet clip.
Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.
|
Remove in this Direction |
Disengage the 4 claws and remove the rear No. 4 air duct as shown in the illustration.
87212G
26.REMOVE REAR NO. 3 AIR DUCT
Disengage the 2 claws and remove the rear No. 3 air duct.
58543B
27.REMOVE FLOOR CARPET BRACKET RH
|
Remove in this Direction |
Remove the clip.
Disengage the claw to remove the floor carpet bracket RH as shown in the illustration.
58544B
28.REMOVE FLOOR CARPET BRACKET LH
|
Remove in this Direction |
Remove the clip.
Disengage the claw to remove the floor carpet bracket LH as shown in the illustration.
58861B
29.REMOVE NO. 1 CONSOLE BOX DUCT
|
Remove in this Direction |
Remove the No. 1 console box duct as shown in the illustration.
55215D
30.REMOVE NO. 3 DASH PANEL INSULATOR PAD
| *a | Cut |
Cut each claw of the 2 clips and remove the No. 3 dash panel insulator pad.
If the No. 3 dash panel insulator pad is damaged, replace it with a new one.
Remove the 2 clips.
55306A
31.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
for LHD:
| *a | Earth Wire |
Remove the bolt and disconnect the earth wire.
Disengage each clamp.
for RHD:
| *a | Earth Wire |
| *b | Relay Block Assembly |
|
Bolt (A) |
|
Bolt (B) |
Remove the bolt (A) and disconnect the earth wire.
Remove the bolt (B).
Disengage each clamp to separate the relay block assembly.
|
Bolt |
|
Screw |
|
Nut |
Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.
55307C
32.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
for LHD:
| *a | Earth Wire |
| *b | Relay Block Assembly |
|
Bolt (A) |
|
Bolt (B) |
Remove the bolt (A) and disconnect the earth wire.
Remove the bolt (B).
Disengage each clamp to separate the relay block assembly.
for RHD:
| *a | Earth Wire |
Remove the bolt and disconnect the earth wire.
Disengage each clamp.
|
Bolt |
|
Screw |
|
Nut |
Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.
55308B
33.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
|
Bolt |
|
Nut |
Disengage each clamp.
Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.
34.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)
89980
35.REMOVE HYBRID VEHICLE CONTROL ECU ASSEMBLY (for LHD)
82877
36.REMOVE ECU INTEGRATION BOX RH (for RHD)
87201B
37.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY
Disengage the 4 claws to remove the No. 2 air duct sub-assembly.
38.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
for LHD:
Disconnect the connector.
| *a | Earth Wire | *b | Connector Holder |
|
Connector |
|
Bolt |
|
Nut | - | - |
Remove the 3 bolts and disconnect the 3 earth wires.
Remove the 2 nuts and disconnect the connector holder.
Disengage each clamp.
for RHD:
Disconnect each connector.
| *a | Earth Wire | - | - |
|
Connector |
|
Bolt |
Remove the 3 bolts and disconnect the 3 earth wires.
Disengage each clamp.
| *a | Connector Holder |
Remove the 2 nuts and disconnect the connector holder.
Disengage the clamp.
|
Release the lock (1) |
|
Release the lock (2) |
Push down the part (A) in the direction indicated by the arrow (1), to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Disconnect the connector.
Disengage each clamp to separate the instrument panel wire.
Turn back the front floor mat as shown in the illustration.
| *1 | Cooler Unit Drain Hose Grommet |
Disconnect the drain cooler hose.
If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.
Remove the cooler unit drain hose grommet.
Remove the 2 hole plugs.
Remove the 3 bolts.
Remove the 4 bolts (A).
|
Bolt (A) |
|
Bolt (B) |
|
Nut | - | - |
Remove the bolt (B) and disconnect the brake pedal assembly.
Remove the nut.
Disengage each clamp.
| *A | for LHD | *B | for RHD |
| *C | w/o Seat Heater | *D | w/ Seat Heater |
|
Remove in this Direction | - | - |
Disconnect each connector.
Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
39.REMOVE AIR CONDITIONER UNIT ASSEMBLY
Remove the 3 bolts.
| *A | w/ Claw | - | - |
w/ Claw:
Disengage the 2 claws.
Remove the air conditioner unit assembly from the instrument panel reinforcement assembly.