Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2019.02–2021.02
RM33C0E _58 Vehicle Interior _065455 DOOR LOCK _0333669 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
·

Rear door glass sub-assembly

·

Rear door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 74038B 4.REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Hide 74260 6.REMOVE REAR ARMREST ASSEMBLY

Hide 67604 7.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68174A 8.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Hide 67844A 9.REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

Hide 67842E 10.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 67848A 11.REMOVE REAR DOOR NO. 1 VENT SEAL

Hide 67858B 12.REMOVE REAR DOOR PANEL PROTECTOR

Hide 68152C 13.REMOVE REAR DOOR GLASS RUN

Hide 67872 14.DISCONNECT REAR DOOR WEATHERSTRIP

a.

Disconnect the rear door weatherstrip until the screw of the rear door rear lower window frame sub-assembly is visible.


Hide 67408F 15.REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Hide 68124B 16.REMOVE REAR DOOR QUARTER WINDOW GLASS

Hide 68104 17.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 69060A 18.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

a.
B469780C01
2.844,2.896 2.781,2.615 true 2.792,2.906 2.99,3.094 0.198,0.188 10 true *a
*a Release Plate
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.


c.

When reusing the rear door lock with motor assembly:

i.
B469782

Remove the door lock wiring harness seal from the rear door lock with motor assembly.



Hide 69038A 19.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY

a.
B469783

Using a screwdriver, disengage the 2 claws as shown in the illustration.


b.
B469784C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to remove the rear door lock cover sub-assembly as shown in the illustration.


Hide 69740D 20.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B469785C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door lock remote control cable assembly as shown in the illustration.


Hide 69780B 21.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B469786C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door inside locking cable assembly as shown in the illustration.