| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C13A6 | Open or Short Circuit in Motor | Detection conditions (1)
·
Diagnosis Condition: Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pushed to lock side with power switch off ·
Malfunction Status: Power supply voltage and +B voltage are normal, but parking brake motor circuit ·
Detection Time: Approximately 1 to 2 seconds Detection conditions (2)
·
Diagnosis Condition: Power switch turned from off to on (IG) ·
Malfunction Status: Overcurrent detected continuously from parking brake motor circuit ·
Detection Time: Approximately 1 second Detection conditions (3)
·
Diagnosis Condition: With the power switch on (IG), the electric parking brake switch (electric parking brake switch assembly) is changed from lock to release or release to lock 3 times repeatedly ·
Malfunction Status: Overcurrent detected continuously from parking brake motor circuit ·
Detection Time: - |
·
Parking brake actuator assembly ·
Wire harness or connector ·
Parking brake ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | ||||||
|---|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | Pattern 5 | ||
| Diagnosis Condition | Power switch on (IG) | ○ | - | - | - | - |
| Electric parking brake switch (electric parking brake switch assembly) pushed to lock side with power switch off | - | ○ | - | - | - | |
| Power switch turned from off to on (IG) | - | - | ○ | - | - | |
| With power switch on (IG), electric parking brake switch (electric parking brake switch assembly) is changed from lock to release 3 times repeatedly | - | - | - | ○ | - | |
| With power switch on (IG), electric parking brake switch (electric parking brake switch assembly) is changed from release to lock 3 times repeatedly | - | - | - | - | - | |
| Malfunction Status | Voltage of power supplied to ECU is normal but malfunction exists in parking brake motor circuit | ○ | ○ | - | - | ○ |
| Overcurrent is detected in the parking brake motor circuit continuously. | - | - | ○ | ○ | ○ | |
| Detection Time | Approximately 1 to 2 seconds | Approximately 1 to 2 seconds | Approximately 1 second | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.
The parking brake indicator light blinks (red) when the power switch is turned on (IG) after replacing the parking brake ECU (brake actuator assembly). Operate the electric parking brake switch (electric parking brake switch assembly) to turn off the parking brake indicator light (red).
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Electric Parking Brake / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Permission of RH Interlocking PKB Lock | Parking brake actuator assembly RH parking brake lock control permission status | OK or NG | OK | - |
| Permission of LH Interlocking PKB Lock | Parking brake actuator assembly RH parking brake lock control permission status | OK or NG | OK | - |
| Tester Display |
|---|
| Permission of RH Interlocking PKB Lock |
| Permission of LH Interlocking PKB Lock |
| Proceed to |
|---|
| NEXT |
NEXT
| *A | RH | *B | LH |
| *a | Front view of Parking Brake Wire Assembly | *b | (to wire harness connector) |
| *c | (to Parking Brake Actuator Assembly) | - | - |
Remove the parking brake wire assembly.
Check the parking brake wire assembly for damage.
No damage.
If damaged, there may be a short in the wire harness or a short to ground.
Inspect the parking brake wire assembly.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uR2-1 (MRR-) - u1-1 (RE-) | Always | Below 1 Ω |
| uR2-1 (MRR-) - u1-2 (RE+) | Always | 10 kΩ or higher |
| uR2-1 (MRR-) or u1-1 (RE-) - Body ground | Always | 10 kΩ or higher |
| uR2-2 (MRR+) - u1-2 (RE+) | Always | Below 1 Ω |
| uR2-2 (MRR+) - u1-1 (RE-) | Always | 10 kΩ or higher |
| uR2-2 (MRR+) or u1-2 (RE+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| vR2-1 (MRL-) - v1-1 (LE-) | Always | Below 1 Ω |
| vR2-1 (MRL-) - v1-2 (LE+) | Always | 10 kΩ or higher |
| vR2-1 (MRL-) or v1-1 (LE-) - Body ground | Always | 10 kΩ or higher |
| vR2-2 (MRL+) - v1-2 (LE+) | Always | Below 1 Ω |
| vR2-2 (MRL+) - v1-1 (LE-) | Always | 10 kΩ or higher |
| vR2-2 (MRL+) or v1-2 (LE+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Make sure the parking brake wire assembly is securely installed.
Disconnect the A44 parking brake ECU (brake actuator assembly) connector.
Disconnect the u1 or v1 parking brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A44-4 (MRR+) - u1-2 (RE+) | Always | Below 1 Ω |
| A44-3 (MRR-) - u1-1 (RE-) | Always | Below 1 Ω |
| A44-4 (MRR+) or u1-2 (RE+) - Body ground | Always | 10 kΩ or higher |
| A44-3 (MRR-) or u1-1 (RE-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A44-7 (MRL+) - v1-2 (LE+) | Always | Below 1 Ω |
| A44-8 (MRL-) - v1-1 (LE-) | Always | Below 1 Ω |
| A44-7 (MRL+) or v1-2 (LE+) - Body ground | Always | 10 kΩ or higher |
| A44-8 (MRL-) or v1-1 (LE-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the parking brake actuator assembly.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(for RHD)>REMOVAL
NG