Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR › from 2019.02
RM33C0E _58 Vehicle Interior _065464 HEATING / AIR CONDITIONING _0331713 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
E371432

When replacing the compressor with motor assembly with a new one, gradually discharge the inert gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

(Oil capacity inside the new compressor with motor assembly: 120 to 135 cc (4.06 to 4.56 fl. oz)) - (Remaining oil amount in the removed compressor with motor assembly) = (Oil amount to be removed from the new compressor)


NOTICE:
·

If a new compressor with motor assembly is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor with motor assembly is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 is used, compressor with motor assembly insulation performance may decrease, resulting in leakage of electric power.




Hide 88370 2.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

a.

Using an E8 "TORX" socket wrench, temporarily install the compressor with motor assembly with the 2 stud bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
E371430C03
1.333,1.917 1.49,2.115 0.156,0.198 10 false 1 0.594,1.802 0.75,2 0.156,0.198 10 false 2 0.75,0.167 0.906,0.365 0.156,0.198 10 false 3
V100135

Bolt
V100136

Nut


Install the compressor with motor assembly with the bolt and 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolt and nuts in the order shown in the illustration.



c.
E371429C02
1.302,0.531 1.594,0.313 true 2.604,2.073 2.833,1.875 true 2.552,2.781 2.865,3.125 true 1.615,0.198 1.927,0.354 0.313,0.156 10 false *c 2.844,3.135 3.156,3.292 0.313,0.156 10 false *b 2.865,1.75 3.177,1.906 0.313,0.156 10 false *a
*a Connector (A)
*b Connector (B)
*c Green-colored Lock
V100137

Slide


Connect the connector (B).


d.

Remove the insulating tape from the connector (A).


e.

Connect the connector (A) and slide the green-colored lock as shown in the illustration to securely lock it.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Make sure that the connector is connected securely.



f.

Connect the 2 connectors.


Hide 88711 3.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the No. 1 cooler refrigerant discharge hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88704 4.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 17750A 5.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 6.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 8.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT