Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2019.02–2021.02
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331860 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during spiral cable sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Removal/installation of the spiral cable with sensor sub-assembly Steering angle neutral point (Initialize parking support brake system) Parking Support Brake System (Click here)
Steering angle setting Parking Assist Monitor System (Click here)
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Parking Support Brake System*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)

Hide 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 64718C 4.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45186 6.REMOVE LOWER NO. 2 STEERING WHEEL COVER

Hide 45130 7.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 8.REMOVE STEERING WHEEL ASSEMBLY

Hide 45024 9.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

Hide 45024 10.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

Hide 45286B 11.REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

Hide 45286B 12.REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

Hide 13.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the power switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the front wheels are aligned facing straight ahead.


d.
B468688C01
0.823,2.417 1.094,2.125 1.094,2.125 1.469,2.125 true 1.5,2.052 1.677,2.25 0.177,0.198 10 false *a
*a Slider
V113147

Release in this Direction


Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.

Disconnect the other connectors from the spiral cable with sensor sub-assembly.


f.
B468689C01
2.354,1.385 2.51,1.583 0.156,0.198 10 false .
V113147

Separate in this Direction


Separate the wire harness from the spiral cable with sensor sub-assembly as shown in the illustration.


g.
B468691

Disengage the claw and 2 clips to remove the spiral cable with sensor sub-assembly.


Hide 14.REMOVE SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly or the steering sensor.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in the center position of the steering sensor becoming misaligned. Therefore, make sure to use the lock pin provided with a new spiral cable sub-assembly when removing the steering sensor from the spiral cable sub-assembly.

·


a.
C372704

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable sub-assembly.

·

Do not remove the lock pin before installing the steering sensor to the spiral cable sub-assembly.




b.
B471941C01
0.615,0.781 0.479,0.542 0.479,0.542 0.302,0.542 true 3.135,0.615 2.885,0.615 2.885,0.615 2.802,0.76 true 2.375,0.719 2.021,0.875 2.021,0.875 2.406,0.979 true 1.844,0.792 2.083,1.031 0.24,0.24 10 false *a 0.135,0.469 0.354,0.667 0.219,0.198 10 false *b 3.156,0.542 3.375,0.74 0.219,0.198 10 false *b
*a Guide
*b Pin


Disengage the 6 claws and 2 pins to remove the spiral cable sub-assembly from the steering sensor.

NOTICE:

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.