The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during lower No. 1 instrument panel airbag assembly removal/installation are shown below.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
64718C
2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67914
4.REMOVE FRONT DOOR SCUFF PLATE
62112A
5.REMOVE COWL SIDE TRIM SUB-ASSEMBLY
62312B
6.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the instrument side panel.
55318C
7.REMOVE INSTRUMENT SIDE PANEL
55606
8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
55606
9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
55436B
10.REMOVE NO. 2 METER HOOD CLUSTER
53601
11.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
55302D
12.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
55435B
13.REMOVE NO. 1 METER HOOD CLUSTER
55434B
14.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL
73900
15.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)
|
Deployment Side |
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Remove the 4 bolts.
Disengage the 2 claws and separate the lower No. 1 instrument panel airbag assembly.
When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.
| *a | Protective Tape |
| *b | Airbag Connector |
| *c | Airbag Connector Locking Button |
|
Release in this Direction |
Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.
Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
73900
16.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)
|
Deployment Side |
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Remove the 4 bolts.
Disengage the 2 claws and separate the lower No. 1 instrument panel airbag assembly.
When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.
| *a | Protective Tape |
| *b | Airbag Connector |
| *c | Airbag Connector Locking Button |
|
Release in this Direction |
Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.
Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.