When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the headlight ECU sub-assembly LH/RH and illuminates the clearance lights.
When the operation conditions of the daytime running lights are met, the main body ECU (multiplex network body ECU) sends an illumination request signal to the headlight ECU sub-assembly LH/RH and illuminates the daytime running lights.
for Bulb Type Turn Signal Light
for LED Type Turn Signal Light
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Check the illumination of each clearance lights and daytime running lights.
| Result | Proceed to |
|---|---|
| LH side clearance light and daytime running light does not illuminate | A |
| RH side clearance light and daytime running light does not illuminate | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Clearance Light | Clearance lights | OFF or ON | - |
| Daytime Running Light | Daytime running lights | OFF or ON | - |
| Tester Display |
|---|
| Clearance Light |
| Tester Display |
|---|
| Daytime Running Light |
Clearance lights and daytime running lights illuminate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the headlight unit assembly LH with RH and connect the connectors.
for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
for LED Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the clearance lights and daytime running lights.
The clearance lights and daytime running lights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for Bulb Type Turn Signal Light | A |
| for LED Type Turn Signal Light | B |
A
B
| *a | Component without harness connected
(to Headlight ECU Sub-assembly LH) |
*b | Component without harness connected
(to No. 1 Headlight Clearance LED Unit LH) |
Remove the headlight assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
Remove the No. 1 headlight clearance LED unit LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-20 (DRL+) - G-1 | Always | Below 1 Ω |
| B-11 (DRL-) - G-3 | Always | Below 1 Ω |
| B-19 (CLL+) - G-2 | Always | Below 1 Ω |
| G-4 - H-5 | Always | Below 1 Ω |
| G-5 - H-4 | Always | Below 1 Ω |
| G-6 - H-3 | Always | Below 1 Ω |
| G-7 - H-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
| *a | Component without harness connected
(to Headlight ECU Sub-assembly LH) |
*b | Component without harness connected
(to Headlight Lens LH) |
Remove the headlight assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>REMOVAL
Remove the headlight lens LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-10 (DRL/CLL+) - E-7 | Always | Below 1 Ω |
| B-1 (DRL/CLL-) - E-8 | Always | Below 1 Ω |
| B-16 (PWM1) - E-6 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling (Sub) / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Clearance Light | Clearance lights | OFF or ON | - |
| Daytime Running Light | Daytime running lights | OFF or ON | - |
| Tester Display |
|---|
| Clearance Light |
| Tester Display |
|---|
| Daytime Running Light |
Clearance lights and daytime running lights illuminate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the headlight unit assembly RH with LH and connect the connectors.
for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
for LED Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the clearance lights and daytime running lights.
The clearance lights and daytime running lights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for Bulb Type Turn Signal Light | A |
| for LED Type Turn Signal Light | B |
A
B
| *a | Component without harness connected
(to Headlight ECU Sub-assembly RH) |
*b | Component without harness connected
(to No. 1 Headlight Clearance LED Unit RH) |
Remove the headlight assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
Remove the No. 1 headlight clearance LED unit RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-20 (DRL+) - G-1 | Always | Below 1 Ω |
| B-11 (DRL-) - G-3 | Always | Below 1 Ω |
| B-19 (CLL+) - G-2 | Always | Below 1 Ω |
| G-4 - H-5 | Always | Below 1 Ω |
| G-5 - H-4 | Always | Below 1 Ω |
| G-6 - H-3 | Always | Below 1 Ω |
| G-7 - H-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
| *a | Component without harness connected
(to Headlight ECU Sub-assembly RH) |
*b | Component without harness connected
(to Headlight Lens RH) |
Remove the headlight assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>REMOVAL
Remove the headlight lens RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-10 (DRL/CLL+) - E-7 | Always | Below 1 Ω |
| B-1 (DRL/CLL-) - E-8 | Always | Below 1 Ω |
| B-16 (PWM1) - E-6 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY