When the electric parking brake switch is pulled, a lock request signal is sent from the parking brake ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the parking brake ECU (brake actuator assembly) to the parking brake actuator assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C13B4 | EPB Switch Malfunction | ·
Open or short detected in parking brake switch circuit for 1 second or more ·
Stuck parking brake switch detected (when parked: 30 seconds, when driving: 1 second, during engine stall: 1 second) ·
Stuck parking brake switch detected 3 times in succession when being operated |
·
Electric parking brake switch (electric parking brake switch assembly) ·
Wire harness or connector ·
Parking brake ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | |||||||
|---|---|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | Pattern 5 | Pattern 6 | ||
| Diagnosis Condition | Vehicle is stopped | - | - | ○ | - | - | - |
| Vehicle is being driven | - | - | - | ○ | - | - | |
| During initial check | - | - | - | - | ○ | - | |
| Parking brake switch is being operated | - | - | - | - | - | ○ | |
| Malfunction Status | Open detected in parking brake switch circuit | ○ | - | - | - | - | - |
| Short detected in parking brake switch circuit | - | ○ | - | - | - | - | |
| Stuck parking brake switch detected | - | - | ○ | ○ | ○ | ○ | |
| Detection Time | 1 second or more | 1 second or more | 30 seconds or more | 1 second or more | 1 second or more | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | 1 trip | 3 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.
The parking brake indicator light blinks (red) when the power switch is turned on (IG) after replacing the parking brake ECU (brake actuator assembly). Operate the electric parking brake switch (electric parking brake switch assembly) to turn off the parking brake indicator light (red).
Inspect the electric parking brake switch (electric parking brake switch assembly).
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K37 electric parking brake switch (electric parking brake switch assembly) connector.
Disconnect the A44 parking brake ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A44-14 (SWI1) - K37-9 (SWI1) | Always | Below 1 Ω |
| A44-20 (SWO1) - K37-10 (SWO1) | Always | Below 1 Ω |
| A44-24 (SWI2) - K37-1 (SWI2) | Always | Below 1 Ω |
| A44-22 (SWO2) - K37-2 (SWO2) | Always | Below 1 Ω |
| A44-14 (SWI1) or K37-9 (SWI1) - Body ground | Always | 10 kΩ or higher |
| A44-20 (SWO1) or K37-10 (SWO1) - Body ground | Always | 10 kΩ or higher |
| A44-24 (SWI2) or K37-1 (SWI2) - Body ground | Always | 10 kΩ or higher |
| A44-22 (SWO2) or K37-2 (SWO2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A44-14 (SWI1) - K37-16 (SWI1) | Always | Below 1 Ω |
| A44-20 (SWO1) - K37-15 (SWO1) | Always | Below 1 Ω |
| A44-24 (SWI2) - K37-8 (SWI2) | Always | Below 1 Ω |
| A44-22 (SWO2) - K37-7 (SWO2) | Always | Below 1 Ω |
| A44-14 (SWI1) or K37-16 (SWI1) - Body ground | Always | 10 kΩ or higher |
| A44-20 (SWO1) or K37-15 (SWO1) - Body ground | Always | 10 kΩ or higher |
| A44-24 (SWI2) or K37-8 (SWI2) - Body ground | Always | 10 kΩ or higher |
| A44-22 (SWO2) or K37-7 (SWO2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(for RHD)>REMOVAL
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING