Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD) › from 2019.10
RM33C0E _54 Brake _065443 BRAKE SYSTEM (OTHER) _0319352 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44785D 1.INSTALL BRAKE MASTER CYLINDER GASKET

a.

Install a new brake master cylinder gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C376594C03
2.563,4.292 2.563,4.021 false 1.729,2.99 1.729,2.594 1.729,2.594 1.573,2.594 false 1.417,3.031 1.417,2.833 1.417,2.833 1.26,2.833 false 1.979,2.979 2.188,2.583 2.188,2.583 2.385,2.583 false 0.729,3.625 0.729,3.24 0.729,3.24 0.531,3.24 false 0.323,4.073 0.323,3.802 false 1.094,2.76 1.406,2.917 0.313,0.156 10 false *a 2.427,2.521 2.74,2.677 0.313,0.156 10 false *b 0.26,4.083 0.573,4.24 0.313,0.156 10 false *c 0.365,3.167 0.677,3.323 0.313,0.156 10 false *d 2.5,4.302 2.813,4.458 0.313,0.156 10 false *e 1.438,2.521 1.75,2.677 0.313,0.156 10 false *f
*a Skid Control ECU
*b No. 1 Reservoir Hose
*c Brake Master Cylinder Push Rod Clevis
*d Boot
*e Master Cylinder Reservoir Assembly
*f Brake Actuator Bracket


Install the brake booster with master cylinder assembly with the 4 nuts.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Be careful not to allow brake fluid to enter the connector.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder assembly is filled with brake fluid.




Hide 47264A 3.INSTALL PUSH ROD PIN

a.
C319792C01
0,0 0,0 false
V100144

Lithium Soap Base Glycol Grease


Apply lithium soap base glycol grease to the push rod pin.


b.
C377998

Connect the brake master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.

HINT:

The push rod pin can be installed in either direction.



Hide 5.CONNECT BRAKE LINE

a.
C376593C02
2.875,2.885 2.708,2.885 2.708,2.885 2.708,2.646 false 1.802,2.927 2.115,3.083 0.313,0.156 10 false *a 2.917,2.813 3.229,2.969 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 3 brake lines to the brake booster with master cylinder assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 44571A 6.CONNECT NO. 1 BRAKE ACTUATOR HOSE

a.
C376590C02
1.406,2.833 1.406,2.417 true 1.333,2.823 1.51,2.979 0.177,0.156 10 true *a 1.729,0.323 2.188,0.521 0.458,0.198 10 false 90° 1.688,1.167 2.146,1.365 0.458,0.198 10 false 180°
*a Identification Mark
V100136

Front of the vehicle


Connect the No. 1 brake actuator hose to the brake booster with master cylinder assembly and slide the clip to secure it.

NOTICE:
·

Make sure to connect the No. 1 brake actuator hose with its identification mark facing the front of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 82111 7.INSTALL ENGINE ROOM MAIN WIRE

a.
C376588C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster with master cylinder assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




b.

Engage the clamp to install the engine room main wire.


c.

Connect the connector to the brake booster with master cylinder assembly.


Hide 44551C 8.BLEED NO. 1 BRAKE ACTUATOR TUBE

NOTICE:

Make sure to bleed the air from the No. 1 brake actuator tube. If the air remains in the No. 1 brake actuator tube, the air will enter the brake booster pump assembly and may damage the brake booster pump assembly.


a.

Remove the brake master cylinder reservoir filler cap assembly.


b.

Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT3

SAE J1704 or FMVSS No. 116 DOT4



c.
C378025

Remove the 2 nuts to separate the No. 1 brake actuator tube.

HINT:

If the No. 1 brake actuator tube has already been separated, it is not necessary to perform this step.



d.
C378026N01
2.323,1.208 2.323,0.802 true 0.771,1.417 1.104,1.417 true 2.198,1.219 2.51,1.396 0.313,0.177 10 true SST 0.51,1.333 0.813,1.5 0.302,0.167 10 true SST

Set SST to the brake master cylinder reservoir assembly.

SST
09992-00242  09992-00350  


e.

Using SST, increase and then maintain the pressure in the brake master cylinder reservoir assembly for 60 seconds.(*1)

Standard Pressure:

50 to 80 kPa (0.6 to 0.8 kgf/cm2, 7.3 to 11.6 psi)



f.

Release the pressure in the brake master cylinder reservoir assembly and wait for 30 seconds.(*2)


g.

Repeat steps *1 to *2, 3 times.


h.

Remove SST.


i.
C378027C01
0,0 0,0 false
V113147

Pull up


Elevate the No. 1 brake actuator tube for 10 seconds by lifting the No. 1 brake actuator tube as shown in the illustration.(*3)

NOTICE:

Do not damage the hoses by applying excessive force.



j.

Repeat step *3, 5 times.


k.
C378028C01
0,0 0,0 false
V113147

Pull up


Elevate the No. 1 brake actuator tube for 10 seconds by lifting the No. 1 brake actuator tube as shown in the illustration.(*4)

NOTICE:

Do not damage the hoses by applying excessive force.



l.
C378029C01
0,0 0,0 false
V113147

Press down


Lower the No. 1 brake actuator tube for 10 seconds as shown in the illustration.(*5)

NOTICE:

Do not damage the hoses by applying excessive force.



m.

Repeat steps *4 to *5, 5 times.


n.

Install the No. 1 brake actuator tube with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 9.CONNECT BRAKE BOOSTER PUMP CONNECTOR

HINT:

Perform this operation only when the accumulator pressure zero down operation could not be performed using the GTS.


a.
C378024C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 10.FILL RESERVOIR WITH BRAKE FLUID

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 12.BLEED BRAKE SYSTEM

Hide 13.INSPECT AND ADJUST BRAKE PEDAL

Hide 14. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR

Hide 12601B 15.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53607A 16.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

a.
C377997N02
1,1.927 1.115,2.083 0.115,0.156 10 true A 2.448,1.927 2.552,2.073 0.104,0.146 10 true A 2.833,1.917 2.938,2.063 0.104,0.146 10 true B 0.594,1.917 0.708,2.063 0.115,0.146 10 true B

Temporarily install the front center upper suspension brace sub-assembly with the 6 bolts and 4 nuts.


b.

Fully tighten the 2 nuts (A).

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


c.

Fully tighten the 6 bolts and 2 nuts (B) to install the front center upper suspension brace sub-assembly.

Torque:
Bolt : 8.9 N*m (91 kgf*cm, 79 in.*lbf)
Nut (B) : 39 N*m (398 kgf*cm, 29 ft.*lbf)


d.

Engage the 3 clamps to install the wire harness.


e.

Connect the connector.


Hide 55708 17.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY