If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, telematics transceiver* or speakers.
If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, telematics transceiver* or speakers.
*: w/ Telematics Transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 9 Speakers | B |
A
B
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly
(w/o Telematics Transceiver) |
A |
| Front No. 1 speaker assembly or front No. 2 speaker assembly
(w/ Telematics Transceiver) |
B |
| Rear speaker assembly | C |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
Disconnect the K4 radio and display receiver assembly connector.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-1 (FR+) - K7-4 (TWR+) | Always | Below 1 Ω |
| K4-6 (FR-) - K7-2 (TWR-) | Always | Below 1 Ω |
| K4-2 (FL+) - K8-4 (TWL+) | Always | Below 1 Ω |
| K4-7 (FL-) - K8-2 (TWL-) | Always | Below 1 Ω |
| N1-2 - K7-3 (+) | Always | Below 1 Ω |
| N1-1 - K7-1 (-) | Always | Below 1 Ω |
| O1-2 - K8-3 (+) | Always | Below 1 Ω |
| O1-1 - K8-1 (-) | Always | Below 1 Ω |
| K4-1 (FR+) or K7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K4-6 (FR-) or K7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| K4-2 (FL+) or K8-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K4-7 (FL-) or K8-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| N1-2 or K7-3 (+) - Body ground | Always | 10 kΩ or higher |
| N1-1 or K7-1 (-) - Body ground | Always | 10 kΩ or higher |
| O1-2 or K8-3 (+) - Body ground | Always | 10 kΩ or higher |
| O1-1 or K8-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K4 radio and display receiver assembly connector.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
Disconnect the K157 telematics transceiver connector.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-1 (FR+) - K157-2 (SPI+) | Always | Below 1 Ω |
| K4-6 (FR-) - K157-3 (SPI-) | Always | Below 1 Ω |
| K157-5 (SPO+) - K7-4 (TWR+) | Always | Below 1 Ω |
| K157-6 (SPO-) - K7-2 (TWR-) | Always | Below 1 Ω |
| K4-2 (FL+) - K8-4 (TWL+) | Always | Below 1 Ω |
| K4-7 (FL-) - K8-2 (TWL-) | Always | Below 1 Ω |
| N1-2 - K7-3 (+) | Always | Below 1 Ω |
| N1-1 - K7-1 (-) | Always | Below 1 Ω |
| O1-2 - K8-3 (+) | Always | Below 1 Ω |
| O1-1 - K8-1 (-) | Always | Below 1 Ω |
| K4-1 (FR+) or K157-2 (SPI+) - Body ground | Always | 10 kΩ or higher |
| K4-6 (FR-) or K157-3 (SPI-) - Body ground | Always | 10 kΩ or higher |
| K4-2 (FL+) or K8-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K4-7 (FL-) or K8-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K157-5 (SPO+) or K7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K157-6 (SPO-) or K7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| N1-2 or K7-3 (+) - Body ground | Always | 10 kΩ or higher |
| N1-1 or K7-1 (-) - Body ground | Always | 10 kΩ or higher |
| O1-2 or K8-3 (+) - Body ground | Always | 10 kΩ or higher |
| O1-1 or K8-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SPI+) - 5 (SPO+) | Always | Below 1 Ω |
| 3 (SPI-) - 6 (SPO-) | Always | Below 1 Ω |
| 2 (SPI+) - 3 (SPI-) | Always | 10 kΩ or higher |
| 5 (SPO+) - 6 (SPO-) | Always | 10 kΩ or higher |
| 2 (SPI+) or 5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| 3 (SPI-) or 6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the K4 radio and display receiver assembly connector.
Disconnect the Q8 and P8 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-4 (RR+) - P8-2 | Always | Below 1 Ω |
| K4-9 (RR-) - P8-1 | Always | Below 1 Ω |
| K4-3 (RL+) - Q8-2 | Always | Below 1 Ω |
| K4-8 (RL-) - Q8-1 | Always | Below 1 Ω |
| K4-4 (RR+) or P8-2 - Body ground | Always | 10 kΩ or higher |
| K4-9 (RR-) or P8-1 - Body ground | Always | 10 kΩ or higher |
| K4-3 (RL+) or Q8-2 - Body ground | Always | 10 kΩ or higher |
| K4-8 (RL-) or Q8-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 3 speaker assembly | A |
| Front No. 2 speaker assembly
(w/ Telematics Transceiver) |
B |
| Front No. 2 speaker assembly
(w/o Telematics Transceiver) |
C |
| Rear speaker assembly | D |
| Rear stereo component speaker assembly | E |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
E
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-15 (FR+) - K109-4 (+TW) | Always | Below 1 Ω |
| K14-30 (FR-) - K109-2 (-TW) | Always | Below 1 Ω |
| K14-13 (FL+) - K110-4 (+TW) | Always | Below 1 Ω |
| K14-28 (FL-) - K110-2 (-TW) | Always | Below 1 Ω |
| N1-2 - K109-3 (+) | Always | Below 1 Ω |
| N1-1 - K109-1 (-) | Always | Below 1 Ω |
| O1-2 - K110-3 (+) | Always | Below 1 Ω |
| O1-1 - K110-1 (-) | Always | Below 1 Ω |
| K14-15 (FR+) or K109-4 (+TW) - Body ground | Always | 10 kΩ or higher |
| K14-30 (FR-) or K109-2 (-TW) - Body ground | Always | 10 kΩ or higher |
| K14-13 (FL+) or K110-4 (+TW) - Body ground | Always | 10 kΩ or higher |
| K14-28 (FL-) or K110-2 (-TW) - Body ground | Always | 10 kΩ or higher |
| N1-2 or K109-3 (+) - Body ground | Always | 10 kΩ or higher |
| N1-1 or K109-1 (-) - Body ground | Always | 10 kΩ or higher |
| O1-2 or K110-3 (+) - Body ground | Always | 10 kΩ or higher |
| O1-1 or K110-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Inspect the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
Disconnect the K157 telematics transceiver connector.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-14 (TWR+) - K157-2 (SPI+) | Always | Below 1 Ω |
| K14-29 (TWR-) - K157-3 (SPI-) | Always | Below 1 Ω |
| K157-5 (SPO+) - K94-2 (TWR+) | Always | Below 1 Ω |
| K157-6 (SPO-) - K94-1 (TWR-) | Always | Below 1 Ω |
| K14-12 (TWL+) - K95-2 (TWL+) | Always | Below 1 Ω |
| K14-27 (TWL-) - K95-1 (TWL-) | Always | Below 1 Ω |
| K14-14 (TWR+) or K157-2 (SPI+) - Body ground | Always | 10 kΩ or higher |
| K14-29 (TWR-) or K157-3 (SPI-) - Body ground | Always | 10 kΩ or higher |
| K14-12 (TWL+) or K95-2 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K14-27 (TWL-) or K95-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K157-5 (SPO+) or K94-2 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K157-6 (SPO-) or K94-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SPI+) - 5 (SPO+) | Always | Below 1 Ω |
| 3 (SPI-) - 6 (SPO-) | Always | Below 1 Ω |
| 2 (SPI+) - 3 (SPI-) | Always | 10 kΩ or higher |
| 5 (SPO+) - 6 (SPO-) | Always | 10 kΩ or higher |
| 2 (SPI+) or 5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| 3 (SPI-) or 6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-14 (TWR+) - K94-2 (TWR+) | Always | Below 1 Ω |
| K14-29 (TWR-) - K94-1 (TWR-) | Always | Below 1 Ω |
| K14-12 (TWL+) - K95-2 (TWL+) | Always | Below 1 Ω |
| K14-27 (TWL-) - K95-1 (TWL-) | Always | Below 1 Ω |
| K14-14 (TWR+) or K94-2 (TWR+) - Body ground | Always | 10 kΩ or higher |
| K14-29 (TWR-) or K94-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| K14-12 (TWL+) or K95-2 (TWL+) - Body ground | Always | 10 kΩ or higher |
| K14-27 (TWL-) or K95-1 (TWL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the P8 and Q8 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-11 (RR+) - P8-2 | Always | Below 1 Ω |
| K14-26 (RR-) - P8-1 | Always | Below 1 Ω |
| K14-9 (RL+) - Q8-2 | Always | Below 1 Ω |
| K14-24 (RL-) - Q8-1 | Always | Below 1 Ω |
| K14-11 (RR+) or P8-2 - Body ground | Always | 10 kΩ or higher |
| K14-26 (RR-) or P8-1 - Body ground | Always | 10 kΩ or higher |
| K14-9 (RL+) or Q8-2 - Body ground | Always | 10 kΩ or higher |
| K14-24 (RL-) or Q8-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the K14 stereo component amplifier assembly connector.
Disconnect the R1 rear stereo component speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-10 (WF1+) - R1-4 (WF1+) | Always | Below 1 Ω |
| K14-25 (WF1-) - R1-3 (WF1-) | Always | Below 1 Ω |
| K14-8 (WF2+) - R1-2 (WF2+) | Always | Below 1 Ω |
| K14-23 (WF2-) - R1-1 (WF2-) | Always | Below 1 Ω |
| K14-10 (WF1+) or R1-4 (WF1+) - Body ground | Always | 10 kΩ or higher |
| K14-25 (WF1-) or R1-3 (WF1-) - Body ground | Always | 10 kΩ or higher |
| K14-8 (WF2+) or R1-2 (WF2+) - Body ground | Always | 10 kΩ or higher |
| K14-23 (WF2-) or R1-1 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear stereo component speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>REMOVAL
Inspect the rear stereo component speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG