Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442440 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P1C8449  High Voltage Power Resource Circuit Short during Ready ON  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU assembly monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects an open circuit malfunction.

HINT:
·

This DTC is differentiated from P300449 based on detection timing (after power switch is turned on (READY)). If P300449 is also output at the same time, first perform troubleshooting for P300449.

·

If there is a SMRG stuck open malfunction, only P1C8449 is output.



The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH or VL) internal circuit malfunction
·

Voltage sensor (VH or VL) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

HV battery malfunction

·

HV battery junction block assembly malfunction

·

Inverter with converter assembly malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction


Low-voltage circuit (12 V) malfunction
·

Hybrid vehicle control ECU assembly malfunction

·

HV battery junction block assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C8449 High Voltage Power Resource Circuit Short during Ready ON High-voltage circuit malfunctions between the HV battery and inverter with converter assembly.
The voltage before boosting continues to be out of the HV battery voltage range or the integrated value of variation amount of the voltage before boosting for a specified period of time is large while the power switch is on (READY).
The EV electric battery fuse in the service plug grip is blown, the service plug grip is removed, SMRB or SMRG remains open, or the high-voltage cable has an open circuit.
(1 trip detection logic)
·

HV battery junction block assembly

·

Wire harness or connector

·

Hybrid vehicle control ECU assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P1C8449
·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery Current

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting



The following items can be helpful when performing repairs:

Data List
·

Ready Signal


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) and wait for 3 minutes or more.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.


7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, HV BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control, Motor Generator and HV Battery / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1C8449 only is output, or P0A9563 and DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of motor generator control system in the tables below are output. C
DTCs of hybrid battery system in the tables below are output. D
P0A9563 is also output. E


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
Motor generator control system P0A1B1F Generator Control Module Circuit Intermittent
P0A1A47 Generator Control Module Watchdog / Safety μC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
Hybrid battery system P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
Power source circuit malfunction Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Hybrid battery system P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Motor generator control system P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
Motor generator control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold
Hybrid battery system P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open
P0B1362 Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure
System malfunction Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P0E311C Boosting Converter Voltage Sensor "A" Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P300449 High Voltage Power Resource Circuit Short during Pre-Charge
Motor generator control system P1CB69E Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On
P0CA300 DC/DC Converter Step Up Voltage Performance


HINT:
·

P1C8449 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




e.

Turn the power switch off.



A

2.CLEAR DTC

B

C

D

E

2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL, HV BATTERY)
3.CHECK DTC OUTPUT (HYBRID CONTROL, HV BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and HV Battery / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1C8449 only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of hybrid battery system in the tables below are output. C


Malfunction Content System Relevant DTC
System malfunction Hybrid control system P1AC413 Hybrid/EV Battery Stack 1 Current Interrupt Device Circuit Open
Hybrid battery system P1AC413 Hybrid/EV Battery Stack 1 Current Interrupt Device Circuit Open
P1AC49E Hybrid/EV Battery Stack 1 Current Interrupt Device Stuck On
P1AC513 Hybrid/EV Battery Stack 2 Current Interrupt Device Circuit Open
P1AC59E Hybrid/EV Battery Stack 2 Current Interrupt Device Stuck On


HINT:
·

P1C8449 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




e.

Turn the power switch off.



A

4.CHECK DTC OUTPUT (HYBRID CONTROL)

B

C

4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

With the vehicle stopped, apply the parking brake and turn the power switch on (READY).

HINT:
·

If the power switch could not be turned on (READY), turn the power switch off and check for DTCs after turning the power switch on (READY) again.

·

Because P300449 uses 2 trip detection logic, the DTC detection conditions need to be met 2 times.




c.

Ensure the safety of the areas in front and at the back of the vehicle.


d.

Move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time.

HINT:

Depressing both the accelerator pedal and brake pedal at the same time causes the HV battery current to flow and ensures that there is no problem with the high-voltage wiring.



e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P1C8449 is output, or no DTCs are output. A
Power switch could not be turned on (READY) and DTC P300449 is output. B



g.

Turn the power switch off.



A

5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

B

5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

OK

6.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

6.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

7.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the R22 HV battery junction block assembly connector.


d.

Disconnect the K69 hybrid vehicle control ECU assembly connector.


e.
A455718C26
1.146,1.74 1.542,1.99 0.396,0.25 0.51,3.656 0.906,3.906 0.396,0.25 1.667,2.302 2.031,1.823 true 1.021,4.115 1.375,3.667 true 2.917,2.271 2.24,1.833 true 2.24,4.156 2.031,3.667 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.594,2.844 0.906,3 0.313,0.156 10 false *b 1.24,2.229 1.854,2.427 0.615,0.198 10 false SMRB 0.854,4.177 1.469,4.375 0.615,0.198 10 false SMRB 0.594,3.698 1.052,3.896 0.458,0.198 10 false R22 1.208,1.781 1.667,1.979 0.458,0.198 10 false K69 2.802,2.281 3.417,2.479 0.615,0.198 10 false SMRG 2.094,4.198 2.708,4.396 0.615,0.198 10 false SMRG
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K69-4 (SMRB) - R22-1 (SMRB) Power switch off Below 1 Ω
K69-1 (SMRG) - R22-4 (SMRG) Power switch off Below 1 Ω



f.

Reconnect the K69 hybrid vehicle control ECU assembly connector.


g.

Reconnect the R22 HV battery junction block assembly connector.


h.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the R22 HV battery junction block assembly connector.


d.
A436194C20
0.781,0.99 1.115,1.25 0.333,0.26 1.823,1.229 2.292,1.823 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.354,1.74 2.667,1.896 0.313,0.156 10 false GND 0.833,1.042 1.188,1.281 0.354,0.24 10 false R22
*a Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R22-3 (GND) - Body ground Power switch off Below 1 Ω



e.

Reconnect the R22 HV battery junction block assembly connector.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

10.CHECK HV BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HV BATTERY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric vehicle battery plug assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY PLUG (for LITHIUM-ION BATTERY)>REMOVAL


c.
A405689N08
1.969,0.583 2.344,0.833 0.375,0.25 1.771,1.604 2.146,1.875 0.375,0.271 1.99,0.604 2.302,0.802 0.313,0.198 10 true z23 1.802,1.646 2.104,1.844 0.302,0.198 10 true z27

Disconnect the z23 and z27 HV battery high voltage connectors.


d.
A407228C16
0.479,1.135 0.854,1.396 0.375,0.26 0.042,3.24 0.417,3.5 0.375,0.26 0.573,1.177 0.885,1.375 0.313,0.198 10 false z23 0.125,3.292 0.438,3.49 0.313,0.198 10 false z27 0.417,0.313 0.729,0.469 0.313,0.156 10 false *a 0.313,2.448 0.625,2.604 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 2 HV Battery Junction Block Assembly)
*b Front view of wire harness connector
(to No. 1 HV Battery Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z23-1 - z27-1 (-) Power switch off 30 V or higher



e.

Reconnect the z23 and z27 HV battery high voltage connectors.


f.

Install the electric vehicle battery plug assembly.


Result:
Proceed to
OK
NG



OK

11.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

13.REPLACE BATTERY ECU ASSEMBLY
11.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

12.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK FOR NORMAL OPERATION)
12.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK FOR NORMAL OPERATION)
CAUTION:

Be sure to wear insulated gloves.


a.

Install the service plug grip.


b.

Turn the power switch on (IG).


c.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

d.

Turn the power switch off and wait for 2 minutes or more.


e.

Turn the power switch on (READY).


f.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid/EV Battery Voltage, VL-Voltage before Boosting.


g.

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.

Powertrain > Hybrid Control > Data List
Tester Display
VL-Voltage before Boosting
Hybrid/EV Battery Voltage
50003 397 150,227

Result:
Result Proceed to
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. A
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more. B


h.

Turn the power switch off.



A

END

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

13.REPLACE BATTERY ECU ASSEMBLY

NEXT

14.SIMULATION TEST
14.SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Turn the power switch off and wait for 2 minutes or more.


f.

Turn the power switch on (IG) and wait for 2 minutes or more.


g.

Enter the following menus: Powertrain / Hybrid Control and HV Battery / Trouble Codes.


h.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > HV Battery > Trouble Codes
50001 398

Result:
Result Proceed to
No DTCs are output. A
DTCs of hybrid battery system are output. B


i.

Turn the power switch off.



A

END

B