G92DH
1.INSPECT NO. 1 HV BATTERY INTAKE FILTER
G920G
2.TEMPORARILY INSTALL NO. 4 HV BATTERY END PLATE SUB-ASSEMBLY
Be sure to wear insulated gloves.
Temporarily install the No. 4 HV battery end plate sub-assembly to the HV battery with the 2 bolts and 2 nuts.
Fully tighten the 2 nuts.
G920K
3.INSTALL NO. 5 HV BATTERY END PLATE SUB-ASSEMBLY
Be sure to wear insulated gloves.
Install the No. 5 HV battery end plate sub-assembly to the HV battery with the 12 nuts.
G920TA
4.INSTALL NO. 4 HV BATTERY SHIELD SUB-ASSEMBLY
Be sure to wear insulated gloves.
Install the No. 4 HV battery shield sub-assembly to the HV battery with the 4 nuts.
G920SA
5.INSTALL NO. 3 HV BATTERY SHIELD SUB-ASSEMBLY
Be sure to wear insulated gloves.
Install the No. 3 HV battery shield sub-assembly to the HV battery with the 4 nuts.
G920G
6.INSTALL NO. 4 HV BATTERY END PLATE SUB-ASSEMBLY
Be sure to wear insulated gloves.
Fully tighten the 2 bolts.
G9510
7.INSTALL HV BATTERY
Be sure to wear insulated gloves.
| *a | Bolt (A)
(Bolt Length: 25 mm (0.984 in.)) |
| *b | Bolt (B)
(Bolt Length: 24 mm (0.945 in.)) |
| *c | Bolt (C)
(Bolt Length: 65 mm (2.559 in.)) |
Install the HV battery to the vehicle body with the 3 bolts (A), bolt (B) and bolt (C).
Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.
To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.
Use cardboard or another similar material to protect the HV battery and vehicle body from damage.
Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.
When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.
While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.
As bolts with 3 different lengths are used, make sure to install each bolt to the correct position.
If the HV battery has been struck or dropped, replace it.
82161
8.CONNECT FLOOR WIRE
Be sure to wear insulated gloves.
Connect the HV battery connector.
Engage the clamp.
G92PF
9.INSTALL NO. 4 HV BATTERY PROTECTOR
Be sure to wear insulated gloves.
Engage the clamp to install the No. 4 HV battery protector to the HV battery.
82161
10.CONNECT FLOOR WIRE
Be sure to wear insulated gloves.
Engage the 2 clamps to install the floor wire to the HV battery.
899A0A
11.INSTALL NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY
G9290A
12.INSTALL HYBRID BATTERY HOSE ASSEMBLY
Engage the 2 claws to install the hybrid battery hose assembly to the HV battery.
Connect the hybrid battery hose assembly to the vehicle.
82161
13.CONNECT FLOOR WIRE
Be sure to wear insulated gloves.
Connect the HV battery junction block assembly connector.
Connect the electric vehicle battery plug assembly connector.
Engage the clamp.
821H1
14.CONNECT FLOOR UNDER WIRE
Be sure to wear insulated gloves.
Connect the floor wire connector.
Connect the shield ground to the HV battery.
Connect the 2 HV battery junction block assembly connectors.
Make sure that the connectors are connected securely.
G92N4A
15.INSTALL NO. 1 HV BATTERY COVER PANEL RH
Be sure to wear insulated gloves.
| *1 | Battery Cover Lock Striker |
| *a | Button |
| *b | Push |
Install the No. 1 HV battery cover panel RH to the HV battery with the 3 bolts and 3 nuts.
Install the battery cover lock striker, then push the button to lock it.
G9230
16.INSTALL BATTERY COOLING BLOWER ASSEMBLY
G3834
17.INSTALL SERVICE PLUG GRIP
18.PERFORM INITIALIZATION