When selecting SPORT mode, the switch operation signal is sent to the hybrid vehicle control ECU assembly. Following this, the system enters SPORT mode and the vehicle will be driven using SPORT mode. This signal is then transmitted from the hybrid vehicle control ECU assembly via CAN to the combination meter assembly to illuminate the SPORT mode indicator.
| Result | Proceed to |
|---|---|
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Sport Mode Switch, Normal Mode Switch.
| Tester Display |
|---|
| Sport Mode Switch |
| Normal Mode Switch |
Read the value displayed on the GTS.
| Result | Proceed to |
|---|---|
| The GTS display changes according to the electric parking brake switch assembly operation. | A |
| The GTS display does not change according to the electric parking brake switch assembly operation. | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COMBINATION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K37 electric parking brake switch assembly connector.
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Electric Parking Brake Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K37-16 (GND1) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K37-9 (GND1) - Body ground | Always | Below 1 Ω |
Reconnect the K37 electric parking brake switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K69 and K70 hybrid vehicle control ECU assembly connectors.
Disconnect the K37 electric parking brake switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
*b | Front view of wire harness connector
(to Electric Parking Brake Switch Assembly) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-6 (SPRT) - K37-12 (P) | Always | Below 1 Ω |
| K70-6 (SPRT) or K37-12 (P) - Body ground | Always | 10 kΩ or higher |
| K69-10 (NORM) - K37-13 (B) | Always | Below 1 Ω |
| K69-10 (NORM) or K37-13 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-6 (SPRT) - K37-13 (P) | Always | Below 1 Ω |
| K70-6 (SPRT) or K37-13 (P) - Body ground | Always | 10 kΩ or higher |
| K69-10 (NORM) - K37-12 (B) | Always | Below 1 Ω |
| K69-10 (NORM) or K37-12 (B) - Body ground | Always | 10 kΩ or higher |
Reconnect the K37 electric parking brake switch assembly.
Reconnect the K69 and K70 hybrid vehicle control ECU assembly connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG