Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442936 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P0A8111  Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground  


DESCRIPTION

The battery cooling blower assembly speed is controlled by the battery ECU assembly. Power is supplied to the battery cooling blower assembly when the MREL terminal of the hybrid vehicle control ECU assembly turns on the IGCT relay. The battery ECU assembly sends command signals (SI0) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The frequency (FP0) of the battery cooling blower assembly is sent to the battery ECU assembly as a monitor signal.

A377319E02
0.26,2.344 2.385,2.76 2.125,0.417 10 false Battery Cooling Blower Assembly 2.99,1.104 4.865,1.667 1.875,0.563 10 false SI0 (Command Signal) 2.979,1.948 4.625,2.458 1.646,0.51 10 false FP0 (Monitor Signal) 5.156,2.427 6.885,2.75 1.729,0.323 10 false Battery ECU Assembly

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A8111 Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground Both of the following conditions are met:
·

The speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range.

·

The battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking).


(1 trip detection logic)
·

Battery cooling blower assembly

·

Battery ECU assembly

·

BATT FAN fuse

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0A8111
·

Hybrid/EV Battery Cooling Fan 1 Drive Request

·

Hybrid/EV Battery Cooling Fan 1 Drive Status

·

Hybrid/EV Battery Cooling Fan 1 Frequency



The following items can be helpful when performing repairs:

Data List
·

Hybrid/EV Battery Temperature 1 to 6

·

BATT Voltage


HINT:

"Hybrid/EV Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly speed.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Enter the following menus: Powertrain / HV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan.

7.

Select fan mode 1 and operate the battery cooling blower assembly and wait for 60 seconds or more.

HINT:

Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.


8.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A404421E02
1.177,1.198 1.906,1.635 0.729,0.438 10 false MREL 1.688,1.188 2.417,1.625 0.729,0.438 10 false 6 0.479,3.354 2.906,3.927 2.427,0.573 10 false Hybrid Vehicle Control ECU Assembly 0.542,0.271 1.813,0.74 1.271,0.469 10 false Auxiliary Battery 2.521,0.427 3.51,0.885 0.99,0.458 10 false IGCT 3.563,0.802 4.552,1.26 0.99,0.458 10 false IGCT 3.354,0.438 3.677,0.781 0.323,0.344 10 false 1 3.938,0.427 4.26,0.771 0.323,0.344 10 false 2 3.354,0.177 3.677,0.521 0.323,0.344 10 false 3 3.938,0.167 4.26,0.51 0.323,0.344 10 false 5 4.51,0.177 4.833,0.521 0.323,0.344 10 false 1 4.938,0.167 5.26,0.51 0.323,0.344 10 false 2 4.479,0.438 5.469,0.896 0.99,0.458 10 false BATT FAN 3.104,1.625 4.094,2.083 0.99,0.458 10 false SI0 3.115,1.927 4.104,2.385 0.99,0.458 10 false GND0 4.229,1.615 5.219,2.073 0.99,0.458 10 false IG0 4.208,1.927 5.198,2.385 0.99,0.458 10 false FP0 2.896,1.615 3.219,1.958 0.323,0.344 10 false 4 2.906,1.927 3.229,2.271 0.323,0.344 10 false 3 4.573,1.615 4.896,1.958 0.323,0.344 10 false 2 4.573,1.906 4.896,2.25 0.323,0.344 10 false 1 2.76,2.365 5.323,2.938 2.563,0.573 10 false R24 Battery Cooling Blower Assembly 5.521,4.281 7.156,4.646 1.635,0.365 10 false Battery ECU Assembly 5.594,3.781 6.583,4.24 0.99,0.458 10 false GND1 5.594,3.302 6.583,3.76 0.99,0.458 10 false GND 5.594,2.771 6.583,3.229 0.99,0.458 10 false SI0 5.594,1.917 6.583,2.375 0.99,0.458 10 false FP0 5.344,1.917 5.667,2.26 0.323,0.344 10 false 15 5.313,2.76 5.635,3.104 0.323,0.344 10 false 14 5.313,3.208 5.635,3.552 0.323,0.344 10 false 27 5.396,3.667 5.719,4.01 0.323,0.344 10 false 3 0.188,3.365 0.917,3.802 0.729,0.438 10 false A29 5.208,4.292 5.938,4.729 0.729,0.438 10 false z16

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

As the battery cooling blower assembly speed is excessively low, there is a possibility of an open or short to ground in connected circuits, or motor locking.


PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0A8111 only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid battery system in the table below are output. B
DTCs of hybrid control system in the table below are output. C


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


e.

Turn the power switch off.



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID/EV BATTERY COOLING FAN)

B

C

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE HYBRID/EV BATTERY COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Trouble Codes.


d.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

e.

Enter the following menus: Powertrain / HV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan.


f.

Select fan mode 6 in the "Control the Hybrid/EV Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

Powertrain > HV Battery > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid/EV Battery Cooling Fan Change the battery cooling blower assembly operation and blower volume. 0, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > HV Battery > Active Test
Tester Display
Control the Hybrid/EV Battery Cooling Fan
50004 398 1
NOTICE:

If the Active Test cannot be performed, skip it and proceed to the next step to check if the fan operates and air is sucked. In accordance with fail-safe system operation, the battery ECU assembly sends a command to operate the battery cooling blower assembly.



g.

Check that the battery cooling blower assembly operates, air is sucked into the inlet duct and the operation sound is normal.

HINT:

The battery cooling blower assembly may not stop even when turning the cooling fan off in the "Control the Hybrid/EV Battery Cooling Fan" Active Test. This is due to HV system control and is not a malfunction.


OK:

The battery cooling blower assembly operates.



h.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)

NG

7.CHECK FUSE (BATT FAN)
3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406229N06
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Disconnect the z16 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A406231N03
1.396,0.635 1.844,0.906 0.448,0.271 1.458,0.656 1.781,0.865 0.323,0.208 10 true R24

Disconnect the R24 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A407419C04
1.521,0.26 1.885,0.51 0.365,0.25 1.531,3.167 1.896,3.417 0.365,0.25 0.427,1.271 1.396,2.104 true 1.948,3.802 2.385,3.688 true 0.385,0.115 0.958,0.625 0.573,0.51 10 false *a 0.865,3 1.281,3.458 0.417,0.458 10 false *b 1.625,0.313 2.198,0.823 0.573,0.51 10 false z16 1.604,3.219 2.177,3.729 0.573,0.51 10 false R24 0.167,1.177 0.74,1.688 0.573,0.51 10 false FP0 2.448,3.604 3.021,4.115 0.573,0.51 10 false FP0
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R24-1 (FP0) - z16-15 (FP0) Power switch off Below 1 Ω
z16-15 (FP0) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z16-15 (FP0) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check the condition of each wire harness and each connector between the battery ECU assembly connector and battery cooling blower assembly.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the R24 battery cooling blower assembly connector.


l.

Reconnect the z16 battery ECU assembly connector.


m.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (HYBRID/EV BATTERY COOLING FAN 1 FREQUENCY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (HYBRID/EV BATTERY COOLING FAN 1 FREQUENCY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the GTS to the DLC3.


e.

Turn the power switch on (IG).


f.

Enter the following menus: Powertrain / HV Battery / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

h.

Enter the following menus: Powertrain / HV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan / Data List / Hybrid/EV Battery Cooling Fan 1 Frequency.


i.

Select each fan mode 1 to 6 in the "Control the Hybrid/EV Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

Powertrain > HV Battery > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid/EV Battery Cooling Fan Change the battery cooling blower assembly operation and blower volume. 0, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > HV Battery > Active Test
Active Test Display
Control the Hybrid/EV Battery Cooling Fan
Data List Display
Hybrid/EV Battery Cooling Fan 1 Frequency
50004 398 1 54
NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the battery ECU assembly sends a command to operate the battery cooling fan assembly.



j.
A406502C03
1.479,2.344 1.948,2.625 0.469,0.281 0.948,4.031 1.479,3.583 true 1.865,3.25 2.677,2.875 true 0.083,0.083 0.354,0.313 0.271,0.229 10 true *a 1.615,2.396 2.021,2.667 0.406,0.271 10 false R20 0.792,4.063 1.198,4.333 0.406,0.271 10 false FP0 2.76,2.802 3.167,3.073 0.406,0.271 10 false GND
*a Component with harness connected
(Battery ECU Assembly)


While the cooling fan is operating, compare the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery ECU assembly connector.

Specified Condition:
Tester Connection Condition
R20-14 (FP0) - R20-4 (GND) Battery cooling blower assembly operating (Active Test of cooling fan being performed)


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Result Proceed to
Both of the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) and the actual measured value at the battery ECU assembly connector are 0 Hz. A
Other than above B



k.

Turn the power switch off.


l.

Disconnect the cable from the negative (-) auxiliary battery terminal.


m.

Install the No. 4 HV battery protector.



A

5.CHECK BATTERY ECU ASSEMBLY

B

6.CHECK BATTERY ECU ASSEMBLY (FREQUENCY)
5.CHECK BATTERY ECU ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


c.
A406231N03
1.396,0.635 1.844,0.906 0.448,0.271 1.458,0.656 1.781,0.865 0.323,0.208 10 true R24

Disconnect the R24 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A369910C45
1.583,0.354 2.021,0.635 0.438,0.281 1.99,0.99 2.448,0.729 true 1.99,1.229 2.479,1.521 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.667,0.385 2.323,0.906 0.656,0.521 10 false R24 2.531,0.594 3.115,1.219 0.583,0.625 10 false FP0 2.552,1.531 3.104,1.844 0.552,0.313 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R24-1 (FP0) - R24-3 (GND0) Power switch on (IG) 4.5 to 5.5 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the R24 battery cooling blower assembly connector.


j.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

6.CHECK BATTERY ECU ASSEMBLY (FREQUENCY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the GTS to the DLC3.


e.

Turn the power switch on (IG).


f.

Enter the following menus: Powertrain / HV Battery / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

h.

Enter the following menus: Powertrain / HV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan / Data List / Hybrid/EV Battery Cooling Fan 1 Frequency.


i.

Select each fan mode 1 to 6 in the "Control the Hybrid/EV Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

Powertrain > HV Battery > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid/EV Battery Cooling Fan Change the battery cooling blower assembly operation and blower volume. 0, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > HV Battery > Active Test
Active Test Display
Control the Hybrid/EV Battery Cooling Fan
Data List Display
Hybrid/EV Battery Cooling Fan 1 Frequency
50004 398 1 54
NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the battery ECU assembly sends a command to operate the battery cooling blower assembly.



j.
A406502C03
1.479,2.344 1.948,2.625 0.469,0.281 0.948,4.031 1.479,3.583 true 1.865,3.25 2.677,2.875 true 0.083,0.083 0.354,0.313 0.271,0.229 10 true *a 1.615,2.396 2.021,2.667 0.406,0.271 10 false R20 0.792,4.063 1.198,4.333 0.406,0.271 10 false FP0 2.76,2.802 3.167,3.073 0.406,0.271 10 false GND
*a Component with harness connected
(Battery ECU Assembly)


While the cooling fan is operating, compare the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery ECU assembly connector.

Specified Condition:
Tester Connection Condition Specified Condition
R20-14 (FP0) - R20-4 (GND) Battery cooling blower assembly operating (Active Test of cooling fan being performed) Difference between the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) and the actual measured value at the battery ECU assembly connector is 10% or less.


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.



k.

Turn the power switch off.


l.

Disconnect the cable from the negative (-) auxiliary battery terminal.


m.

Install the No. 4 HV battery protector.


Result:
Proceed to
OK
NG



OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

7.CHECK FUSE (BATT FAN)
a.
A407420C03
2.229,1.917 2.729,1.917 true 0.135,0.073 0.792,0.708 0.656,0.635 10 false *1 2.771,1.844 3.094,2.156 0.323,0.313 10 false *2
*1 No. 4 Relay Block
*2 BATT FAN Fuse


Remove the BATT FAN fuse from the No. 4 relay block.


b.

Measure the resistance of the BATT FAN fuse.

Standard Resistance:
Tester Connection Condition Specified Condition
BATT FAN fuse Power switch off Below 1 Ω



c.

Install the BATT FAN fuse.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)

NG

17.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


c.
A406231N03
1.396,0.635 1.844,0.906 0.448,0.271 1.458,0.656 1.781,0.865 0.323,0.208 10 true R24

Disconnect the R24 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Connect the GTS to the DLC3.


f.

Turn the power switch on (IG).


g.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


h.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

i.
A369910C46
1.583,0.354 2.021,0.635 0.438,0.281 1.042,0.781 1.583,1 true 2,1.188 2.542,1.406 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.667,0.385 2.323,0.906 0.656,0.521 10 false R24 0.729,0.688 1.313,1.313 0.583,0.625 10 false IG0 2.563,1.438 3.198,1.729 0.635,0.292 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R24-2 (IG0) - R24-3 (GND0) Power switch on (IG) 11 to 14 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)

·

Fuse condition (before and after removing fuse(s)) (IG circuit)

·

Connection condition of connectors (IG circuit)

·

Wire harness condition (IG circuit)

·

Wire harness condition (GND circuit)




j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.


l.

Reconnect the R24 battery cooling blower assembly connector.


m.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406229N06
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Disconnect the z16 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the battery ECU assembly and battery cooling blower assembly is not loose or disconnected.




d.
A406231N03
1.396,0.635 1.844,0.906 0.448,0.271 1.458,0.656 1.781,0.865 0.323,0.208 10 true R24

Disconnect the R24 battery cooling blower assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A407419C06
1.521,0.26 1.885,0.51 0.365,0.25 1.531,3.167 1.896,3.417 0.365,0.25 0.615,0.854 1.302,2.094 true 0.833,4.333 1.417,4.156 true 0.385,0.115 0.958,0.625 0.573,0.51 10 false *a 0.865,3 1.281,3.458 0.417,0.458 10 false *b 1.583,0.313 2.156,0.823 0.573,0.51 10 false z16 1.594,3.208 2.167,3.719 0.573,0.51 10 false R24 0.354,0.74 0.729,1.063 0.375,0.323 10 false SI0 0.635,4.292 1.156,4.604 0.521,0.313 10 false SI0
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z16-14 (SI0) - R24-4 (SI0) Power switch off Below 1 Ω
R24-4 (SI0) - Body ground and other terminals Power switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery ECU assembly and battery cooling blower assembly is not loose or disconnected and its terminals are not deformed or corroded.



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R24-4 (SI0) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

Check the condition of each wire harness and each connector between the battery ECU assembly connector and battery cooling blower assembly.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the R24 battery cooling blower assembly connector.


l.

Reconnect the z16 battery ECU assembly connector.


m.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

10.CHECK BATTERY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK BATTERY ECU ASSEMBLY

b.

Measure the resistance according to the value(s) in the table below.

A406222C08
4.135,1.25 4.5,1.448 0.365,0.198 4.625,1.875 5.906,1.031 true 4.542,1.979 5.938,3.604 true 0.125,0.135 0.729,0.521 0.604,0.385 10 false *a 4.177,1.26 4.458,1.427 0.281,0.167 10 true z16 5.948,0.969 6.375,1.177 0.427,0.208 10 false SI0 6,3.583 6.427,3.792 0.427,0.208 10 false GND
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
z16-14 (SI0) -z16-27 (GND) Power switch off 10 kΩ or higher



c.

Install the battery ECU assembly.


Result:
Proceed to
OK
NG



OK

11.CHECK BATTERY ECU ASSEMBLY (SI0 VOLTAGE)

NG

11.CHECK BATTERY ECU ASSEMBLY (SI0 VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A406502C04
1.479,2.344 1.948,2.625 0.469,0.281 0.948,4.031 1.75,3.573 true 1.844,3.25 2.677,2.875 true 0.083,0.083 0.354,0.313 0.271,0.229 10 true *a 1.615,2.396 2.021,2.667 0.406,0.271 10 false R20 0.792,4.063 1.198,4.333 0.406,0.271 10 false SI0 2.76,2.802 3.167,3.073 0.406,0.271 10 false GND
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R20-12 (SI0) -R20-4 (GND) Power switch on (IG) 4.5 to 5.5 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 4 HV battery protector.


Result:
Proceed to
OK
NG



OK

12.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

REPLACE BATTERY COOLING BLOWER ASSEMBLY

12.CHECK BATTERY COOLING BLOWER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Connect the GTS to the DLC3.


e.

Turn the power switch on (IG).


f.

Enter the following menus: Powertrain / HV Battery / Trouble Codes.


g.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

h.

Enter the following menus: Powertrain / HV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan.


i.

Select each fan mode (1 to 6) in the "Control the Hybrid/EV Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

Powertrain > HV Battery > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Hybrid/EV Battery Cooling Fan Change the battery cooling blower assembly operation and blower volume. 0, 1, 2, 3, 4, 5, 6 Intake air temperature -10°C (14°F) or higher
Powertrain > HV Battery > Active Test
Tester Display
Control the Hybrid/EV Battery Cooling Fan
50004 398 1
NOTICE:

If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the battery ECU assembly sends a command to operate the battery cooling blower assembly.



j.
A406502C04
1.479,2.344 1.948,2.625 0.469,0.281 0.948,4.031 1.75,3.573 true 1.844,3.25 2.677,2.875 true 0.083,0.083 0.354,0.313 0.271,0.229 10 true *a 1.615,2.396 2.021,2.667 0.406,0.271 10 false R20 0.792,4.063 1.198,4.333 0.406,0.271 10 false SI0 2.76,2.802 3.167,3.073 0.406,0.271 10 false GND
*a Component with harness connected
(Battery ECU Assembly)


Connect an oscilloscope to the R20 battery ECU assembly connector and check the waveform.

Item Content
Tester Connection R20-12 (SI0) - R20-4 (GND)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Battery cooling blower assembly operating (Active Test of cooling fan being performed)

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:
·

Perform this inspection with the battery ECU assembly connector connected.

·

The wave length will vary with the operating speed of the battery cooling blower assembly.



Result:
Result Proceed to
Normal (The pulse output of waveform 1) A
No pulse generation B



k.

Turn the power switch off.


l.

Disconnect the cable from the negative (-) auxiliary battery terminal.


m.
A284431C04
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a
*a Waveform 1


Install the No. 4 HV battery protector.



A

REPLACE BATTERY COOLING BLOWER ASSEMBLY

B

13.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


c.
A406231N03
1.396,0.635 1.844,0.906 0.448,0.271 1.458,0.656 1.781,0.865 0.323,0.208 10 true R24

Disconnect the R24 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A369910C47
1.583,0.354 2.021,0.635 0.438,0.281 1.969,1.229 2.51,1.448 true 0.229,0.135 0.813,0.76 0.583,0.625 10 false *a 1.667,0.385 2.323,0.906 0.656,0.521 10 false R24 2.583,1.427 3.219,1.813 0.635,0.385 10 false GND0
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R24-3 (GND0) - Body ground Power switch off Below 1 Ω



e.

Connect the R24 battery cooling blower assembly connector.


f.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406229N06
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Disconnect the z16 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A407388C27
1.49,0.396 1.938,0.635 0.448,0.24 2.24,3.115 1.375,2.406 true 0.146,0.115 0.604,0.531 0.458,0.417 10 false *a 1.646,0.427 2.104,0.844 0.458,0.417 10 false z16 2.313,3.083 2.927,3.292 0.615,0.208 10 false GND
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z16-27 (GND) - Body ground Power switch off Below 1 Ω



e.

Reconnect the z16 battery ECU assembly connector.


f.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406229N06
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Disconnect the z16 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A407388C28
1.49,0.396 1.938,0.635 0.448,0.24 2.229,3.115 1.375,2.188 true 0.146,0.115 0.604,0.531 0.458,0.417 10 false *a 1.646,0.427 2.104,0.844 0.458,0.417 10 false z16 2.313,3.083 2.927,3.292 0.615,0.208 10 false GND1
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z16-3 (GND1) - Body ground Power switch off Below 1 Ω



e.

Reconnect the z16 battery ECU assembly connector.


f.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the IGCT relay from the No. 6 relay block.

NOTICE:

Check the terminals of the relay for deformation and corrosion.



c.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


d.
A406231N03
1.396,0.635 1.844,0.906 0.448,0.271 1.458,0.656 1.781,0.865 0.323,0.208 10 true R24

Disconnect the R24 battery cooling blower assembly connector.

NOTICE:
·

Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.

·

Before disconnecting the connector, check that it is not loose or disconnected.




e.

Measure the resistance according to the value(s) in the table below.

A467956C01
0.896,0.667 1.313,0.927 0.417,0.26 2.802,1.135 2.208,0.823 true 5.292,1.26 4.698,0.948 true 0.51,1.646 0.885,1.333 true 0.26,0.542 0.573,0.74 0.313,0.198 10 false *a 2.24,0.115 2.552,0.313 0.313,0.198 10 false *A 4.719,0.104 5.031,0.302 0.313,0.198 10 false *B 2.031,0.719 2.344,0.917 0.313,0.198 10 false *1 4.51,0.823 4.823,1.021 0.313,0.198 10 false *1 3.104,0.281 3.417,0.479 0.313,0.198 10 false *2 5.271,0.281 5.583,0.479 0.313,0.198 10 false *2 0.99,0.719 1.302,0.917 0.313,0.198 10 false R24 0.354,1.667 0.667,1.865 0.313,0.198 10 false IG0
*A LHD *B RHD
*1 No. 6 Relay Block *2 IGCT Relay Holder
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
IGCT relay holder 5 - R24-2 (IG0) Power switch off Below 1 Ω


NOTICE:
·

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

·

Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.




f.

Reconnect the R24 battery cooling blower assembly connector.


g.

Install the rear seat cushion leg sub-assembly.


h.

Install the IGCT relay to the No. 6 relay block.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the BATT FAN fuse from the No. 4 relay block.


c.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


d.
A406231N03
1.396,0.635 1.844,0.906 0.448,0.271 1.458,0.656 1.781,0.865 0.323,0.208 10 true R24

Disconnect the R24 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A407422C04
1.521,0.156 1.927,0.396 0.406,0.24 1,0.74 1.469,0.74 true 0.281,1.479 0.979,2.104 0.698,0.625 10 false *1 1.031,0.052 1.458,0.49 0.427,0.438 10 false *a 2.594,3.094 2.979,3.417 0.385,0.323 10 false *b 1.625,0.198 2.323,0.823 0.698,0.625 10 false R24 0.75,0.677 1.177,1.115 0.427,0.438 10 false IG0
*1 No. 4 Relay Block
*a Front view of wire harness connector
(to Battery Cooling Blower Assembly)
*b BATT FAN Fuse Terminal


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R24-2 (IG0) - Terminals other than 2 (BATT FAN fuse) and body ground Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



f.

Reconnect the R24 battery cooling blower assembly connector.


g.

Install the rear seat cushion leg sub-assembly.


h.

Install the BATT FAN fuse to the No. 4 relay block.


Result:
Proceed to
OK
NG



OK

18.CHECK BATTERY COOLING BLOWER ASSEMBLY

NG

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
18.CHECK BATTERY COOLING BLOWER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


c.
A406231N03
1.396,0.635 1.844,0.906 0.448,0.271 1.458,0.656 1.781,0.865 0.323,0.208 10 true R24

Disconnect the R24 battery cooling blower assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A369912C11
1.552,0.281 1.938,0.583 0.385,0.302 0.99,1.479 1.552,1.229 true 1.938,0.979 2.5,0.729 true 0.208,0.115 0.781,0.625 0.573,0.51 10 false *a 1.615,0.313 2.188,0.823 0.573,0.51 10 false R24 2.583,0.635 3.156,1.146 0.573,0.51 10 false IG0 0.531,1.396 1.104,1.906 0.573,0.51 10 false GND0
*a Component without harness connected
(Battery Cooling Blower Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R24-2 (IG0) - R24-3 (GND0) and Body ground Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



e.

Reconnect the R24 battery cooling blower assembly connector.


f.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (BATT FAN)

NG

19.REPLACE BATTERY COOLING BLOWER ASSEMBLY
19.REPLACE BATTERY COOLING BLOWER ASSEMBLY

NEXT

REPLACE FUSE (BATT FAN)

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (BATT FAN)