Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0334380 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 89305 1.INSTALL ULTRASONIC SENSOR CUSHION SET

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Install the ultrasonic sensor cushion set as shown in the illustration.

E488345C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 89348R 2.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/o Parking Support Brake System)

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one. Install the rear corner ultrasonic sensor with a new rear corner ultrasonic sensor retainer as a set to the rear bumper assembly.



a.
E459857

Engage the 2 claws to install a new rear corner ultrasonic sensor retainer to the rear corner ultrasonic sensor.


b.

Clean the surface of the rear bumper assembly.

i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Wipe off any adhesive residue with cleaner.



c.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 19 mm (0.748 in.)


Cover the sensor installation hole with a 19 mm (0.748 in.) circular piece of tape.


d.
E459855C01
0,0 0,0 false
V100144

Primer


Using a brush or felt, apply primer or equivalent to the rear corner ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper assembly until the primer has dried.




e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Peel off the release paper from the rear corner ultrasonic sensor retainer.


g.
E459856C01
1.604,1.938 1.604,1.604 false 1.51,1.917 1.823,2.073 0.313,0.156 10 false *a
*a Scribed Line
V100155

Press Here


Align the rear corner ultrasonic sensor retainer with rear corner ultrasonic sensor with the mark on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

·

Ensure that the rear corner ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a rear corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear corner ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear corner ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the rear corner ultrasonic sensor retainer and rear bumper assembly.



Hide 89348J 3.INSTALL ULTRASONIC SENSOR CLIP (w/o Parking Support Brake System)

HINT:

Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.


a.
E459853

Engage the clamp to install the ultrasonic sensor clip to the wire.


Hide 89342 4.INSTALL REAR CORNER ULTRASONIC SENSOR (w/o Parking Support Brake System)

a.

When replacing only the rear corner ultrasonic sensor:

i.
E459852C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the rear corner ultrasonic sensor as shown in the illustration.



b.
E459850C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.


c.

Connect the connector.


Hide 89348R 5.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one.



a.

Clean the surface of the rear bumper assembly.

i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 25 mm (0.984 in.)


Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.


c.

Using a brush or felt, apply primer or equivalent to the rear corner ultrasonic sensor retainer installation area.

E459892C01
0.167,0.083 0.5,0.333 0.333,0.25 12 false *A 3.583,0.083 3.833,0.333 0.25,0.25 12 false *B
*A for RH Side *B for LH Side
V100144

Primer - -


NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper assembly until the primer has dried.




d.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


e.

Peel off the release paper from a new rear corner ultrasonic sensor retainer.


f.

Align the rear corner ultrasonic sensor retainer with rear corner ultrasonic sensor with the mark on the rear bumper assembly and install it as shown in the illustration.

E459893C01
1.833,1.583 1.833,1.344 true 5.333,1.583 5.333,1.344 true 0.167,0.083 0.5,0.333 0.333,0.25 12 false *A 3.583,0.083 3.917,0.333 0.333,0.25 12 false *B 1.74,1.573 1.948,1.781 0.208,0.208 10 true *a 5.26,1.573 5.469,1.781 0.208,0.208 10 true *a
*A for RH Side *B for LH Side
*a Scribed Line - -
V100155

Press Here - -


NOTICE:
·

Ensure that the sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

·

Ensure that the rear corner ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a rear corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear corner ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear corner ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the rear corner ultrasonic sensor retainer and rear bumper assembly.



Hide 89348S 6.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

If a rear center ultrasonic sensor retainer has been removed, replace it with a new one.



a.

Clean the surface of the rear bumper assembly.

i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 25 mm (0.984 in.)


Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.


c.
E459885C01
0,0 0,0 false
V100144

Primer


Using a brush or felt, apply primer or equivalent to the rear center ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper assembly until the primer has dried.




d.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


e.

Peel off the release paper from a new rear center ultrasonic sensor retainer.


f.
E459886C01
1.646,1.885 1.646,1.635 true 1.563,1.896 1.823,2.104 0.26,0.208 10 true *a
*a Scribed Line
V100155

Press Here


Align the rear center ultrasonic sensor retainer with rear center ultrasonic sensor with the mark on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

·

Ensure that the rear center ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a rear center ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear center ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the rear center ultrasonic sensor retainer to the rear bumper assembly. Confirm there is no clearance between the rear center ultrasonic sensor retainer and rear bumper assembly.



Hide 89348J 7.INSTALL ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)

HINT:
·

Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.

·

Use the same procedure for all ultrasonic sensor clips.



a.
E459894

Engage the clamp to install the ultrasonic sensor clip to the wire.


Hide 89342 8.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)

a.
E459890C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the rear corner ultrasonic sensor as shown in the illustration.


b.
E459888C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws as shown in the illustration.


c.

Connect the connector.


Hide 89342A 9.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)

a.
E459883C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the rear center ultrasonic sensor as shown in the illustration.


b.
E459881C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws as shown in the illustration.


c.

Connect the connector.


Hide 10.INSTALL REAR BUMPER ASSEMBLY

Hide 12.PERFORM CALIBRATION (w/ Parking Support Brake System)