Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2021.02
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0332275 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P033511  Crankshaft Position Sensor "A" Circuit Short to Ground  P033515  Crankshaft Position Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and Magneto Resistance Element (MRE) type sensor. The No. 1 crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the crankshaft position sensor signal (NE signal) to detect the crankshaft position and engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P033511 Crankshaft Position Sensor "A" Circuit Short to Ground The crankshaft position sensor output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored SAE Code: P0337
P033515 Crankshaft Position Sensor "A" Circuit Short to Battery or Open The crankshaft position sensor output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored SAE Code: P0338

A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:

The correct waveform is as shown.


ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

If the output voltage transmitted by the crankshaft position sensor remains low or high, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Wait 5 seconds or more [B].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P033511 or P033515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A402625E09
0.927,2.094 3.271,2.354 2.344,0.26 10 false d4 0.927,2.25 3.271,2.51 2.344,0.26 10 false Crankshaft Position Sensor 5.688,2.25 6.5,2.427 0.813,0.177 10 false ECM 5.031,2.25 5.844,2.427 0.813,0.177 10 false C100 5.479,0.833 6.292,1.01 0.813,0.177 10 false 1.5 kΩ 5.563,0.26 6.375,0.438 0.813,0.177 10 false 5 V 4.5,0.438 5.313,0.615 0.813,0.177 10 false 116 4.583,0.99 5.396,1.167 0.813,0.177 10 false 93 4.51,1.521 5.323,1.698 0.813,0.177 10 false 115 2.313,0.438 3.125,0.615 0.813,0.177 10 false 3 2.302,0.979 3.115,1.156 0.813,0.177 10 false 1 2.302,1.521 3.115,1.698 0.813,0.177 10 false 2 1.823,0.438 2.635,0.615 0.813,0.177 10 false VCNE 1.927,0.979 2.74,1.156 0.813,0.177 10 false NE+ 1.948,1.51 2.76,1.688 0.813,0.177 10 false NE- 4.844,0.979 5.656,1.156 0.813,0.177 10 false NE+ 4.844,1.521 5.656,1.698 0.813,0.177 10 false NE- 4.854,0.448 5.667,0.625 0.813,0.177 10 false VCNE

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Turn the power switch on (IG).

(c)

Turn the GTS on.

(d)

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

(e)

Start the engine.

(f)

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

g.

Read the values displayed on the GTS while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
A402448C01
0.26,1.104 0.667,1.354 0.406,0.25 0.76,1.833 1.365,1.458 false 2.76,1.833 2.021,1.458 false 1.74,1.958 1.74,1.469 false 0.208,0.167 0.583,0.438 0.375,0.271 10 false *a 0.406,1.146 0.781,1.417 0.375,0.271 10 false d4 0.438,1.76 0.813,2.031 0.375,0.271 10 false NE+ 1.656,1.979 2.188,2.177 0.531,0.198 10 false NE- 2.823,1.813 3.26,2.042 0.438,0.229 10 false VCNE
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the crankshaft position sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d4-3 (VCNE) - Body ground Power switch on (IG) 4.5 to 5.5 V
d4-1 (NE+) - Body ground Power switch on (IG) 3.0 to 5.0 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d4-3 (VCNE) - d4-1 (NE+) Power switch off 1.425 to 1.575 kΩ
d4-2 (NE-) - Body ground Power switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d4-3 (VCNE) - C100-116 (VCNE) Always Below 1 Ω
d4-2 (NE-) - C100-115 (NE-) Always Below 1 Ω
d4-1 (NE+) - C100-93 (NE+) Always Below 1 Ω
d4-3 (VCNE) or C100-116 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
d4-2 (NE-) or C100-115 (NE-) - Body ground and other terminals Always 10 kΩ or higher
d4-1 (NE+) or C100-93 (NE+) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR