Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › ECM › from 2021.02
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0326945 ECM A

A25A-FXS ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) or frame number registration when replacing the ECM.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION



PROCEDURE

Hide 1. PRECAUTION (for LITHIUM-ION BATTERY)

HV battery learning values are stored in the battery ECU assembly and ECM and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.

NOTICE:
·

Do not replace the battery ECU assembly and ECM at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.

·

Do not replace the battery ECU assembly or ECM with a used one from another vehicle.



a.

Procedure when replacing both battery ECU assembly and ECM:

i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

Replace either ECU.


iii.

Connect the cable to the negative (-) auxiliary battery terminal.


iv.

Turn the power switch on (READY) and wait for 5 minutes or more.


v.

Turn the power switch off and disconnect the cable from the negative (-) auxiliary battery terminal.


vi.

Replace the other ECU.


vii.

Connect the cable to the negative (-) auxiliary battery terminal.


viii.

Check that the power switch can be turned on (READY).

HINT:

If the battery ECU assembly and ECM are replaced at the same time without following the above procedure, replace either the battery ECU assembly and ECM with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.




Hide 2. GPF DEPOSITION VALUES

NOTICE:

Before replacing the ECM, store the volumes of accumulated ash (metal oxide) and PM (Particulate Matter). After replacing the ECM, write the volumes of accumulated ash and PM to the new ECM. (w/ Differential Pressure Sensor)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION


Hide 64718C 3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89661 5.REMOVE ECM

a.

for LHD:

i.
A406018

Rotate the 2 levers while pushing the locks, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



ii.

Remove the bolt and separate the engine wire from the No. 2 ECM bracket.


iii.

Disengage the clamp.


iv.
A406022

Remove the 2 nuts and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.




b.

for RHD:

i.
A406017

Rotate the 2 levers while pushing the locks, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



ii.

Remove the bolt and separate the engine wire from the No. 2 ECM bracket.


iii.

Disengage the 2 clamps.


iv.
A406021

Remove the 2 nuts and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.




Hide 89667E 6.REMOVE NO. 1 ECM BRACKET

a.
A408543C01
0.302,0.052 0.615,0.344 0.313,0.292 12 false *A 0.302,2.354 0.635,2.635 0.333,0.281 12 false *B
*A for LHD
*B for RHD


Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 7.REMOVE NO. 2 ECM BRACKET

a.
A408544C01
0.281,0.094 0.594,0.354 0.313,0.26 12 false *A 0.292,2.333 0.615,2.615 0.323,0.281 12 false *B
*A for LHD
*B for RHD


Remove the 2 screws and No. 2 ECM bracket from the ECM.