Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM › from 2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0465299 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  U030051  Internal Control Module Software Incompatibility Not Programmed  U030057  Internal Control Module Software Incompatibility Invalid/Incompatible Software Component  


DESCRIPTION

The forward recognition camera receives vehicle information from the hybrid vehicle control ECU assembly via the CAN communication line.

When the forward recognition camera is unable to determine the vehicle information from the vehicle information sent from the hybrid vehicle control ECU assembly, the forward recognition camera outputs U030051.

When the vehicle information sent from the hybrid vehicle control ECU assembly does not match the vehicle information stored by the forward recognition camera, the forward recognition camera outputs U030057.

DTC No. Detection Item DTC Detection Condition Trouble Area
U030051 Internal Control Module Software Incompatibility Not Programmed The forward recognition camera cannot confirm the vehicle information from the hybrid vehicle control ECU assembly.
·

Hybrid control system

·

Forward recognition camera

·

Hybrid vehicle control ECU assembly


U030057 Internal Control Module Software Incompatibility Invalid/Incompatible Software Component The vehicle information from the hybrid vehicle control ECU assembly and that stored in the forward recognition camera do not match.
·

Hybrid control system

·

Forward recognition camera

·

Hybrid vehicle control ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT


·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTCs
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
Hybrid control system DTC is not output A
Hybrid control system DTC is output B



A

2.CHECK FOR DTCs (HEALTH CHECK)

B

2.CHECK FOR DTCs (HEALTH CHECK)
a.

Using the GTS, perform a health check.

OK:

ECUs other than the forward recognition camera do not output specification information mismatch DTCs related to the hybrid vehicle control ECU assembly.



Result:
Result Proceed to
DTC is not output A
DTC is output B



A

3.READ VALUE USING GTS

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

3.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Chassis > Front Recognition Camera > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
HV/EV Equipped Information Vehicle information (engine) stored by forward recognition camera Non-HV/EV or HV/EV Non-HV/EV: Gasoline Model
HV/EV: HV Model
If a display different from vehicle specification is output, a forward recognition camera that was used with a different vehicle was installed, or the forward recognition camera may be malfunctioning.
Chassis > Front Recognition Camera > Data List
Tester Display
HV/EV Equipped Information
50003 430 20
HINT:
·

When the specification stored by the forward recognition camera and the vehicle specification do not match, there is a malfunction in the specification information stored by the forward recognition camera. Therefore, replace the forward recognition camera.

·

When the specification stored by the forward recognition camera and the vehicle specification match, an hybrid vehicle control ECU assembly with different specifications may be installed. Therefore, replace the hybrid vehicle control ECU assembly.




Result:
Result Proceed to
Specification stored by the forward recognition camera and vehicle specification do not match A
Specification stored by the forward recognition camera and vehicle specification match B



A

REPLACE FORWARD RECOGNITION CAMERA

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY