Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2021.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C060962  Electric Parking Brake Switch Signal Compare Failure  


DESCRIPTION

When the electric parking brake switch is pulled, a lock request signal is sent from the parking brake ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the parking brake ECU (brake actuator assembly) to the parking brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C060962 Electric Parking Brake Switch Signal Compare Failure
·

Open or short detected in parking brake switch circuit for 1 second or more

·

Stuck parking brake switch detected (when parked: 30 seconds, when driving: 1 second, during engine stall: 1 second)

·

Stuck parking brake switch detected 3 times in succession when being operated


·

Electric parking brake switch (electric parking brake switch assembly)

·

Wire harness and connector

·

Parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the combination meter assembly.

DTC Detection Conditions: C060962
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Vehicle is stopped - - ○ - - -
Vehicle is being driven - - - ○ - -
During initial check - - - - ○ -
Parking brake switch is being operated - - - - - ○
Malfunction Status Open detected in parking brake switch circuit ○ - - - - -
Short detected in parking brake switch circuit - ○ - - - -
Stuck parking brake switch detected - - ○ ○ ○ -
Stuck parking brake switch detected 3 times - - - - - ○
Detection Time 1 second or more 1 second or more 30 seconds or more 1 second or more 1 second or more -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C458574E01
1.365,3.156 3.771,3.604 2.406,0.448 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 5.167,3.677 6.833,4.115 1.667,0.438 10 false Parking Brake ECU (Brake Actuator Assembly) 5.167,3.51 5.604,3.698 0.438,0.188 10 false A44 1.365,2.99 1.802,3.177 0.438,0.188 10 false K37 3.333,1.25 3.771,1.438 0.438,0.188 10 false SWI1 3.26,1.563 3.792,1.75 0.531,0.188 10 false SWO1 3.323,1.865 3.76,2.052 0.438,0.188 10 false SWI2 3.25,2.448 3.781,2.635 0.531,0.188 10 false SWO2 5.469,1.365 5.906,1.552 0.438,0.188 10 false SWI1 5.469,1.656 5.948,1.844 0.479,0.188 10 false SWO1 5.469,1.969 5.906,2.156 0.438,0.188 10 false SWI2 5.469,2.563 5.979,2.75 0.51,0.188 10 false SWO2 3.76,1.25 4.406,1.458 0.646,0.208 10 false 9*1, 16*2 3.75,1.552 4.448,1.792 0.698,0.24 10 false 10*1, 15*2 5.167,1.552 5.406,1.75 0.24,0.198 10 false 20 3.76,1.854 4.427,2.094 0.667,0.24 10 false 1*1, 8*2 3.771,2.438 4.427,2.635 0.656,0.198 10 false 2*1, 7*2 5.156,1.26 5.406,1.458 0.25,0.198 10 false 14 5.167,1.844 5.354,2.042 0.188,0.198 10 false 24 5.156,2.438 5.344,2.635 0.188,0.198 10 false 22 0.385,4.146 2.073,4.344 1.688,0.198 10 false *1: for LHD 0.396,4.427 2.083,4.625 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

If the electric parking brake switch is held near the lock position but not fully in the lock position for 1 second or more, a DTC may be stored due to one of the two contacts being ON while the other is OFF. (This is not a system malfunction.)


PROCEDURE

1.READ VALUE USING GTS (EPB SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Chassis / Electric Parking Brake / Data List.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EPB Switch Electric parking brake switch assembly input Neutral / Apply / Release / Unknown Neutral: Lock switch and release switch are off
Apply: Lock switch on
Release: Release switch on
When not normal, electric parking brake switch release side system may be malfunctioning
HINT:

EPB stands for electric parking brake.


Chassis > Electric Parking Brake > Data List
Tester Display
EPB Switch
50003 485 142

d.

Operate the electric parking brake switch assembly and check that the value of "EPB Switch" in the Data List changes between Apply and Release in accordance with the operation of the switch.

OK:

The value of EPB Switch changes between Apply and Release in accordance with switch operation.



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

4.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Electric Parking Brake > Clear DTCs
50002 485
Result:
Proceed to
NEXT




NEXT

3.CHECK DTC
3.CHECK DTC
a.

Check for DTCs.

Chassis > Electric Parking Brake > Trouble Codes
50001 485

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B

4.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

OK

5.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the K37 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A44-14 (SWI1) - K37-9 (SWI1) Always Below 1 Ω
A44-20 (SWO1) - K37-10 (SWO1) Always Below 1 Ω
A44-24 (SWI2) - K37-1 (SWI2) Always Below 1 Ω
A44-22 (SWO2) - K37-2 (SWO2) Always Below 1 Ω
A44-14 (SWI1) or K37-9 (SWI1) - Body ground Always 10 kΩ or higher
A44-20 (SWO1) or K37-10 (SWO1) - Body ground Always 10 kΩ or higher
A44-24 (SWI2) or K37-1 (SWI2) - Body ground Always 10 kΩ or higher
A44-22 (SWO2) or K37-2 (SWO2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A44-14 (SWI1) - K37-16 (SWI1) Always Below 1 Ω
A44-20 (SWO1) - K37-15 (SWO1) Always Below 1 Ω
A44-24 (SWI2) - K37-8 (SWI2) Always Below 1 Ω
A44-22 (SWO2) - K37-7 (SWO2) Always Below 1 Ω
A44-14 (SWI1) or K37-16 (SWI1) - Body ground Always 10 kΩ or higher
A44-20 (SWO1) or K37-15 (SWO1) - Body ground Always 10 kΩ or higher
A44-24 (SWI2) or K37-8 (SWI2) - Body ground Always 10 kΩ or higher
A44-22 (SWO2) or K37-7 (SWO2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CLEAR DTC
a.

Clear the DTCs.

Chassis > Electric Parking Brake > Clear DTCs
50002 485

b.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC
7.CHECK DTC
a.

Check for DTCs.

Chassis > Electric Parking Brake > Trouble Codes
50001 485

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B