| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C061319 | Right Electric Parking Brake Actuator Circuit Current Above Threshold | When the electric parking brake is operating, overcurrent is detected in the parking brake actuator assembly RH 3 times | ·
Parking brake actuator assembly RH ·
No. 1 parking brake wire assembly ·
Wire harness and connector ·
Parking brake ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the combination meter assembly. |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the uR2 and u1 No. 1 parking brake wire assembly connectors.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of No. 1 Parking Brake Wire Assembly | *b | (to wire harness connector) |
| *c | (to Parking Brake Actuator Assembly RH) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uR2-2 - u1-2 (RE+) | Always | Below 1 Ω |
| uR2-2 or u1-2 (RE+) - Body ground and other terminals | Always | 10 kΩ or higher |
| uR2-1 - u1-1 (RE-) | Always | Below 1 Ω |
| uR2-1 or u1-1 (RE-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure the No. 1 parking brake wire assembly is securely installed.
Disconnect the A44 parking brake ECU (brake actuator assembly) connector.
Disconnect the u1 parking brake actuator assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A44-4 (MRR+) - u1-2 (RE+) | Always | Below 1 Ω |
| A44-4 (MRR+) or u1-2 (RE+) - Body ground | Always | 10 kΩ or higher |
| A44-3 (MRR-) - u1-1 (RE-) | Always | Below 1 Ω |
| A44-3 (MRR-) or u1-1 (RE-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Turn the power switch off.
Make sure the No. 1 parking brake wire assembly is securely installed.
Disconnect the u1 parking brake actuator assembly RH connector.
| *a | Front view of No. 1 Parking Brake Wire Assembly
(to Parking Brake Actuator Assembly RH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u1-2 (RE+) - u1-1 (RE-) | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the uR2 No. 1 parking brake wire assembly connector.
| *a | Front view of wire harness connector
(to No. 1 Parking Brake Wire Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uR2-2 - uR2-1 | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the uR2 No. 1 parking brake wire assembly connector.
Disconnect the A44 parking brake ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector | *b | (to Parking Brake ECU (Brake Actuator Assembly)) |
| *c | (to No. 1 Parking Brake Wire Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uR2-2 or A44-4 (MRR+) - Body ground | Always | Below 1 V |
| uR2-1 or A44-3 (MRR-) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(for RHD)>REMOVAL
NG