Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2021.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C402509E15
0.458,0.719 1.688,0.917 1.229,0.198 10 false EPB NO. 1 0.344,1.323 1.573,1.521 1.229,0.198 10 false ECU-IG1 NO. 3 2.844,1.563 3.302,1.781 0.458,0.219 10 false A44 5.135,1.313 7.01,1.792 1.875,0.479 10 false Combination Meter Assembly 2.833,1.729 4.479,2.458 1.646,0.729 10 false Parking Brake ECU (Brake Actuator Assembly) 2.802,0.542 4.031,0.74 1.229,0.198 10 false BEPB 2.813,1.146 4.042,1.344 1.229,0.198 10 false IG 2.604,0.438 2.979,0.656 0.375,0.219 10 false 9 2.542,1.031 2.917,1.25 0.375,0.219 10 false 26 0.917,3.208 3.344,3.708 2.427,0.5 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light on the combination meter may be malfunctioning.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Chassis > Electric Parking Brake > Trouble Codes
50001 485

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.VEHICLE OPERATION CHECK

B

2.VEHICLE OPERATION CHECK
a.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Lock and release operation is normal and parking brake indicator light turns off or blinks A
Lock and release operation is malfunctioning and parking brake indicator light illuminates or turns off according to switch operation B
Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks C



A

3.INSPECT COMBINATION METER ASSEMBLY

B

INSPECT REAR BRAKE

C

4.CHECK HARNESS AND CONNECTOR (BEPB TERMINAL VOLTAGE)
3.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Park Warning
50004 409 108

b.

Check the combination meter assembly.

OK:

Parking brake indicator light turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (BEPB TERMINAL VOLTAGE)
a.

Turn the power switch off.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-9 (BEPB) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)
a.

Turn the power switch off.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-26 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR