These DTCs are stored when a malfunction occurs in the roof antenna assembly circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C111 | GNSS Antenna Circuit Short to Ground | Current to the roof antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit) |
·
Telematics transceiver ·
Roof antenna assembly ·
Antenna cord sub-assembly (for Type A) ·
Antenna cord sub-assembly (for Type B) ·
No. 2 antenna cord sub-assembly ·
No. 5 antenna cord sub-assembly |
| B15C113 | GNSS Antenna Circuit Open | Current to the roof antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit) |
·
Telematics transceiver ·
Roof antenna assembly ·
Antenna cord sub-assembly (for Type A) ·
Antenna cord sub-assembly (for Type B) ·
No. 2 antenna cord sub-assembly ·
No. 5 antenna cord sub-assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Turn the ignition switch to ON and wait for 10 seconds or more.
Clear the DTCs.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component without harness connected (No. 5 Antenna Cord Sub-assembly) |
Disconnect the K No. 5 antenna cord sub-assembly connector.
| *a | Component without harness connected (No. 5 Antenna Cord Sub-assembly) |
Disconnect the J No. 5 antenna cord sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K-2 - J-2 | Always | Below 1 Ω |
| K-2 or J-2 - Body ground | Always | 10 kΩ or higher |
| K-2a - J-2a | Always | Below 1 Ω |
| K-2a or J-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (No. 2 Antenna Cord Sub-assembly) |
Disconnect the I No. 2 antenna cord sub-assembly connector.
| *a | Component without harness connected (No. 2 Antenna Cord Sub-assembly) |
Disconnect the H No. 2 antenna cord sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I-2 - H-2 | Always | Below 1 Ω |
| I-2 or H-2 - Body ground | Always | 10 kΩ or higher |
| I-2a - H-2a | Always | Below 1 Ω |
| I-2a or H-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Antenna Cord Sub-assembly (for Type A)) |
Disconnect the G antenna cord sub-assembly (for Type A) connector.
| *a | Component without harness connected (Antenna Cord Sub-assembly (for Type A)) |
Disconnect the E antenna cord sub-assembly (for Type A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G-2 - E-1 | Always | Below 1 Ω |
| G-2 or E-1 - Body ground | Always | 10 kΩ or higher |
| G-2a - E-1a | Always | Below 1 Ω |
| G-2a or E-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Antenna Cord Sub-assembly (for Type B)) |
Disconnect the D antenna cord sub-assembly (for Type B) connector.
| *a | Component without harness connected (Antenna Cord Sub-assembly (for Type B)) |
Disconnect the B antenna cord sub-assembly (for Type B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-1 - B-1 | Always | Below 1 Ω |
| D-1 or B-1 - Body ground | Always | 10 kΩ or higher |
| D-1a - B-1a | Always | Below 1 Ω |
| D-1a or B-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the roof antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT