Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0468732 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

DTC C1622 is stored if the television camera controller judges as a result of its self check that the signals or signal lines between the television camera controller and rear television camera assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in Back Camera Signal Open or short in the rear television camera signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Television camera controller



WIRING DIAGRAM

E459941E03
5.125,3.688 6.969,4.073 1.844,0.385 10 false Television Camera Controller 5.083,3.51 5.552,3.813 0.469,0.302 10 false R126 4.25,1.052 5.521,1.594 1.271,0.542 10 false from ACC Relay 0.177,4.177 2.385,4.479 2.208,0.302 10 false Rear Television Camera Assembly 0.177,4.01 0.708,4.24 0.531,0.229 10 false m4 5.302,3.083 5.646,3.396 0.344,0.313 10 false 32 5.302,2.698 5.646,3.01 0.344,0.313 10 false 30 5.302,2.281 5.646,2.594 0.344,0.313 10 false 29 5.563,3.208 6.167,3.448 0.604,0.24 10 false CGND 5.563,2.813 6.167,3.052 0.604,0.24 10 false CV- 5.552,2.417 6.156,2.656 0.604,0.24 10 false CV+ 1.594,0.927 1.938,1.24 0.344,0.313 10 false 6 1.208,1.031 1.74,1.25 0.531,0.219 10 false CB+ 1.615,3.083 1.958,3.396 0.344,0.313 10 false 5 1.104,3.219 1.708,3.458 0.604,0.24 10 false CGND 1.208,2.802 1.813,3.042 0.604,0.24 10 false CV- 1.615,2.698 1.958,3.01 0.344,0.313 10 false 2 1.615,2.281 1.958,2.594 0.344,0.313 10 false 3 1.198,2.427 1.802,2.667 0.604,0.24 10 false CV+ 2.49,1.24 3.542,1.479 1.052,0.24 10 false ECU-ACC 3.333,2.969 3.677,3.281 0.344,0.313 10 false * 4.76,4.281 5.771,4.573 1.01,0.292 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the m4 rear television camera assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
m4-6 (CB+) - Body ground Ignition switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the R126 television camera controller connector.


b.

Disconnect the m4 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-29 (CV+) - m4-3 (CV+) Always Below 1 Ω
R126-30 (CV-) - m4-2 (CV-) Always Below 1 Ω
R126-32 (CGND) - m4-5 (CGND) Always Below 1 Ω
R126-29 (CV+) or m4-3 (CV+) - Body ground Always 10 kΩ or higher
R126-30 (CV-) or m4-2 (CV-) - Body ground Always 10 kΩ or higher
R126-32 (CGND) or m4-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA CONTROLLER (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION CAMERA CONTROLLER (CV-, CGND)
a.

Disconnect the R126 television camera controller connector.


b.
E330226C47
1.969,1.771 1.74,1.771 1.74,1.771 1.646,1.125 true 1.188,1.792 1.354,1.792 1.354,1.792 1.5,1.146 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.719,1.729 1.219,1.885 0.5,0.156 10 false CGND 2.146,1.708 2.646,1.865 0.5,0.156 10 false CV-
*a Component without harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
30 (CV-) - Body ground Always Below 1 Ω
32 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TELEVISION CAMERA CONTROLLER (CGND)

NG

4.CHECK TELEVISION CAMERA CONTROLLER (CGND)
a.
E407111C67
1.417,0.25 1.917,0.5 0.5,0.25 1.51,1.156 1.979,1.948 1.979,1.948 2.229,1.948 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 1.49,0.281 1.99,0.438 0.5,0.156 10 false R126 2.271,1.865 2.833,2.052 0.563,0.188 10 false CGND
*a Component with harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-32 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

5.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)
a.

Remove the television camera controller with the connector still connected.


b.

Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the television camera controller with the connector connected.


E430500C56
0.75,0.292 1.25,0.542 0.5,0.25 1.667,2.083 1.5,2.083 1.5,2.083 1.052,1.104 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.583,2.063 0.75,2.063 0.75,2.063 0.875,1.094 true 1.729,2 2.083,2.198 0.354,0.198 10 false CV+ 0.104,1.99 0.583,2.167 0.479,0.177 10 false CGND 3.365,1.188 3.844,1.365 0.479,0.177 10 false GND 5.271,1.188 5.75,1.365 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.677,0.208 4.156,0.385 0.479,0.177 10 false *b 5.604,0.219 6.083,0.396 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.833,0.333 1.313,0.51 0.479,0.177 10 false R126
*a Component with harness connected
(Television Camera Controller)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.



Measurement Condition
Item Content
Terminal No. (Symbol) R126-29 (CV+) - R126-32 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor system operating

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG