Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0468732 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1683  Side Camera Feedback Malfunction  


DESCRIPTION

This DTC is stored if the television camera controller judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the television camera controller.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1683 Side Camera Feedback Malfunction Side camera feedback malfunction
·

Harness or connector

·

Television camera controller

·

Side television camera assembly RH*1

·

Outer rear view mirror assembly RH*1

·

Side television camera assembly LH*2

·

Outer rear view mirror assembly LH*2



*1: for LHD

*2: for RHD


WIRING DIAGRAM

for LHD
E457467E07
5.781,2.688 6.24,2.885 0.458,0.198 10 false R126 5.792,2.844 6.948,3.479 1.156,0.635 10 false Television Camera Controller 0.625,3.146 3.177,3.531 2.552,0.385 10 false Outer Rear View Mirror Assembly RH 0.635,2.323 2.073,2.719 1.438,0.396 10 false Side Television Camera Assembly RH 0.625,2.958 1.083,3.156 0.458,0.198 10 false N24 6,2.177 6.698,2.417 0.698,0.24 10 false SGND 5.99,1.781 6.688,2.021 0.698,0.24 10 false RGND 6,1.333 6.698,1.573 0.698,0.24 10 false RCV- 5.99,0.948 6.688,1.188 0.698,0.24 10 false RCV+ 5.99,0.563 6.688,0.802 0.698,0.24 10 false RCB+ 3.406,0.406 4.104,0.646 0.698,0.24 10 false RCB+ 3.375,0.781 4.073,1.021 0.698,0.24 10 false RCV+ 3.406,1.167 4.104,1.406 0.698,0.24 10 false RCV- 3.375,1.625 4.073,1.865 0.698,0.24 10 false RGND 5.719,0.427 6.031,0.625 0.313,0.198 10 false 40 5.719,0.823 6.031,1.021 0.313,0.198 10 false 38 5.708,1.208 6.021,1.406 0.313,0.198 10 false 16 5.719,1.646 6.031,1.844 0.313,0.198 10 false 17 5.729,2.052 6.042,2.25 0.313,0.198 10 false 39 3.875,1.625 4.188,1.823 0.313,0.198 10 false 13 3.865,1.188 4.177,1.385 0.313,0.198 10 false 12 3.885,0.771 4.198,0.969 0.313,0.198 10 false 1 3.885,0.396 4.219,0.552 0.333,0.156 10 false 2 4.75,2.104 4.958,2.344 0.208,0.24 10 false * 3.854,3.385 5.615,3.698 1.76,0.313 10 false *: Shielded 1.76,0.438 2.458,0.677 0.698,0.24 10 false RCB+ 1.75,0.823 2.448,1.063 0.698,0.24 10 false RCV+ 1.771,1.219 2.469,1.458 0.698,0.24 10 false RCV- 1.729,1.646 2.427,1.885 0.698,0.24 10 false RGND 2.25,0.365 2.583,0.521 0.333,0.156 10 false 1 2.25,0.698 2.583,0.854 0.333,0.156 10 false 5 2.25,1.115 2.583,1.271 0.333,0.156 10 false 7 2.25,1.573 2.583,1.729 0.333,0.156 10 false 3 0.406,2.323 0.74,2.479 0.333,0.156 10 false B 3.375,2.031 4.073,2.271 0.698,0.24 10 false SGND 3.896,2.042 4.208,2.24 0.313,0.198 10 false 14

for RHD
E457467E08
5.365,2.594 5.823,2.792 0.458,0.198 10 false R126 5.375,2.771 7.156,3.5 1.781,0.729 10 false Television Camera Controller 0.938,3.135 3.292,3.427 2.354,0.292 10 false Outer Rear View Mirror Assembly LH 0.906,2.313 2.344,2.719 1.438,0.406 10 false Side Television Camera Assembly LH 0.938,2.948 1.396,3.146 0.458,0.198 10 false O22 6,2.198 6.698,2.438 0.698,0.24 10 false SGND 6,1.76 6.698,2 0.698,0.24 10 false LGND 6,1.344 6.698,1.583 0.698,0.24 10 false LCV- 6,0.927 6.698,1.167 0.698,0.24 10 false LCV+ 6,0.552 6.698,0.792 0.698,0.24 10 false LCB+ 3.385,0.417 4.083,0.656 0.698,0.24 10 false LCB+ 3.396,0.802 4.094,1.042 0.698,0.24 10 false LCV+ 3.417,1.188 4.115,1.427 0.698,0.24 10 false LCV- 3.354,1.635 4.052,1.875 0.698,0.24 10 false LGND 5.698,0.406 6.01,0.604 0.313,0.198 10 false 12 5.708,0.802 6.021,1 0.313,0.198 10 false 10 5.708,1.208 6.021,1.406 0.313,0.198 10 false 34 5.719,1.646 6.031,1.844 0.313,0.198 10 false 35 5.729,2.063 6.042,2.26 0.313,0.198 10 false 11 3.875,1.646 4.188,1.844 0.313,0.198 10 false 13 3.865,1.198 4.177,1.396 0.313,0.198 10 false 12 3.896,0.802 4.208,1 0.313,0.198 10 false 1 3.885,0.438 4.198,0.635 0.313,0.198 10 false 2 4.75,2.104 4.979,2.292 0.229,0.188 10 false * 1.656,3.49 2.688,3.802 1.031,0.313 10 false *: Shielded 1.74,0.406 2.438,0.646 0.698,0.24 10 false LCB+ 1.74,0.844 2.438,1.083 0.698,0.24 10 false LCV+ 1.76,1.24 2.458,1.479 0.698,0.24 10 false LCV- 1.719,1.656 2.417,1.896 0.698,0.24 10 false LGND 2.24,0.406 2.552,0.604 0.313,0.198 10 false 1 2.25,0.771 2.563,0.969 0.313,0.198 10 false 5 2.25,1.156 2.563,1.354 0.313,0.198 10 false 7 2.25,1.625 2.563,1.823 0.313,0.198 10 false 3 0.375,2.302 0.688,2.5 0.313,0.198 10 false A 3.365,2.031 4.063,2.271 0.698,0.24 10 false SGND 3.906,2.042 4.219,2.24 0.313,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1683 is not output.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY RH)

C

9.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the R126 television camera controller connector.


b.

Disconnect the N24 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-40 (RCB+) - N24-2 (RCB+) Always Below 1 Ω
R126-38 (RCV+) - N24-1 (RCV+) Always Below 1 Ω
R126-16 (RCV-) - N24-12 (RCV-) Always Below 1 Ω
R126-17 (RGND) - N24-13 (RGND) Always Below 1 Ω
R126-40 (RCB+) or N24-2 (RCB+) - Body ground Always 10 kΩ or higher
R126-38 (RCV+) or N24-1 (RCV+) - Body ground Always 10 kΩ or higher
R126-16 (RCV-) or N24-12 (RCV-) - Body ground Always 10 kΩ or higher
R126-17 (RGND) or N24-13 (RGND) - Body ground Always 10 kΩ or higher
R126-39 (SGND) or N24-14 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA CONTROLLER (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION CAMERA CONTROLLER (RCV-, RGND)
a.
E330226C61
1.302,0.396 1.135,0.396 1.135,0.396 0.99,0.99 true 0.615,0.688 0.781,0.688 0.781,0.688 0.938,1 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.177,0.635 0.677,0.792 0.5,0.156 10 false RGND 1.333,0.313 1.833,0.469 0.5,0.156 10 false RCV-
*a Component without harness connected
(Television Camera Controller)


Disconnect the R126 television camera controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
17 (RGND) - Body ground Always Below 1 Ω
16 (RCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TELEVISION CAMERA CONTROLLER (RCB+, RGND)

NG

4.CHECK TELEVISION CAMERA CONTROLLER (RCB+, RGND)
a.
E407111C68
1.417,0.25 1.917,0.5 0.5,0.25 0.698,0.677 0.875,0.677 0.875,0.677 0.938,1 true 0.854,1.146 0.719,1.75 0.719,1.75 0.542,1.75 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.146,1.656 0.615,1.854 0.469,0.198 10 false RCB+ 1.49,0.292 1.99,0.448 0.5,0.156 10 false R126 0.281,0.594 0.844,0.781 0.563,0.188 10 false RGND
*a Component with harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-17 (RGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R126-40 (RCB+) - R126-17 (RGND) Ignition switch ON 5.5 to 7.05 V
R126-40 (RCB+) - R126-17 (RGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

NG

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)
a.

Using an oscilloscope, check the waveform of the side television camera assembly RH.

HINT:

A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the television camera controller with the connector connected.


E430500C58
0.75,0.302 1.25,0.552 0.5,0.25 0.646,0.74 0.5,0.74 0.5,0.74 0.406,0.99 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.74,2.177 0.594,2.177 0.594,2.177 0.469,1.104 true 0.875,2.094 1.344,2.333 0.469,0.24 10 false RCV+ 0.688,0.667 1.167,0.844 0.479,0.177 10 false RGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.823,0.333 1.302,0.51 0.479,0.177 10 false R126
*a Component with harness connected
(Television Camera Controller)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly RH.

·

The video waveform is constantly output when the ignition switch is ACC.



Measurement Condition
Item Content
Tester Connection R126-38 (RCV+) - R126-17 (RGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E461664C09
2.469,0.76 2.969,1.01 0.5,0.25 2.75,2.229 3.25,2.479 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 0.677,1.771 0.927,1.771 0.927,1.771 1.01,2.385 true 1.521,1.74 1.271,1.74 1.271,1.74 1.156,2.365 true 1.51,3.177 1.26,3.177 1.26,3.177 1.177,2.688 true 0.646,3.146 0.896,3.146 0.896,3.146 1.021,2.677 true 1.573,1.667 2.188,1.865 0.615,0.198 10 false RCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false RCB+ 0.573,0.302 1.188,0.5 0.615,0.198 10 false RGND 0.604,1.333 1.219,1.531 0.615,0.198 10 false RCV- 2.49,1.333 3.104,1.531 0.615,0.198 10 false RCV+ 0.333,1.708 0.948,1.906 0.615,0.198 10 false RCV+ 1.552,3.115 2.167,3.313 0.615,0.198 10 false RGND 0.313,3.094 0.927,3.292 0.615,0.198 10 false RCV- 2.667,0.813 3.031,1.031 0.365,0.219 10 false B 2.875,2.292 3.271,2.552 0.396,0.26 10 false N24 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Front view of wire harness connector
(to Vehicle Wire Harness Connector)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (RCB+) - N24-2 (RCB+) Always Below 1 Ω
B-5 (RCV+) - N24-1 (RCV+) Always Below 1 Ω
B-7 (RCV-) - N24-12 (RCV-) Always Below 1 Ω
B-3 (RGND) - N24-13 (RGND) Always Below 1 Ω
B-1 (RCB+) or N24-2 (RCB+) - Body ground Always 10 kΩ or higher
B-5 (RCV+) or N24-1 (RCV+) - Body ground Always 10 kΩ or higher
B-7 (RCV-) or N24-12 (RCV-) - Body ground Always 10 kΩ or higher
B-3 (RGND) or N24-13 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

7.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1683 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG

9.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the R126 television camera controller connector.


b.

Disconnect the O22 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-12 (LCB+) - O22-2 (LCB+) Always Below 1 Ω
R126-10 (LCV+) - O22-1 (LCV+) Always Below 1 Ω
R126-34 (LCV-) - O22-12 (LCV-) Always Below 1 Ω
R126-35 (LGND) - O22-13 (LGND) Always Below 1 Ω
R126-12 (LCB+) or O22-2 (LCB+) - Body ground Always 10 kΩ or higher
R126-10 (LCV+) or O22-1 (LCV+) - Body ground Always 10 kΩ or higher
R126-34 (LCV-) or O22-12 (LCV-) - Body ground Always 10 kΩ or higher
R126-35 (LGND) or O22-13 (LGND) - Body ground Always 10 kΩ or higher
R126-11 (SGND) or O22-14 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK TELEVISION CAMERA CONTROLLER (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TELEVISION CAMERA CONTROLLER (LCV-, LGND)
a.
E330226C62
1.698,1.802 1.469,1.802 1.469,1.802 1.375,1.156 true 0.979,1.792 1.146,1.792 1.146,1.792 1.292,1.146 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.583,1.719 1.083,1.875 0.5,0.156 10 false LGND 1.76,1.719 2.26,1.875 0.5,0.156 10 false LCV-
*a Component without harness connected
(Television Camera Controller)


Disconnect the R126 television camera controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
35 (LGND) - Body ground Always Below 1 Ω
34 (LCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK TELEVISION CAMERA CONTROLLER (LCB+, LGND)

NG

11.CHECK TELEVISION CAMERA CONTROLLER (LCB+, LGND)
a.
E407111C70
1.417,0.25 1.917,0.5 0.5,0.25 0.667,1.917 1,1.917 1,1.917 1.302,1.135 true 0.917,0.667 1.167,0.667 1.167,0.667 1.25,0.958 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.542,0.583 1.031,0.75 0.49,0.167 10 false LCB+ 0.25,1.833 0.813,1.99 0.563,0.156 10 false LGND 1.5,0.281 2,0.438 0.5,0.156 10 false R126
*a Component with harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-35 (LGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R126-12 (LCB+) - R126-35 (LGND) Ignition switch ON 5.5 to 7.05 V
R126-12 (LCB+) - R126-35 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

NG

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)
a.

Using an oscilloscope, check the waveform of the side television camera assembly LH.

HINT:

A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the television camera controller with the connector connected.


E430500C59
0.75,0.292 1.25,0.542 0.5,0.25 0.708,1.104 0.646,2.094 0.646,2.094 0.49,2.094 true 1.104,1.333 0.958,1.333 0.958,1.333 0.802,1.021 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 1.188,1.26 1.917,1.51 0.729,0.25 10 false LCV+ 0.073,2.021 0.552,2.198 0.479,0.177 10 false LGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.833,0.323 1.313,0.5 0.479,0.177 10 false R126
*a Component with harness connected
(Television Camera Controller)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly LH.

·

The video waveform is constantly output when the ignition switch is ACC.



Measurement Condition
Item Content
Tester Connection R126-10 (LCV+) - R126-35 (LGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

13.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
13.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E461664C10
2.469,0.76 2.969,1.01 0.5,0.25 2.75,2.229 3.25,2.479 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 0.677,1.771 0.927,1.771 0.927,1.771 1.01,2.385 true 1.521,1.74 1.271,1.74 1.271,1.74 1.156,2.365 true 1.51,3.177 1.26,3.177 1.26,3.177 1.177,2.688 true 0.646,3.146 0.896,3.146 0.896,3.146 1.021,2.677 true 1.573,1.667 2.188,1.865 0.615,0.198 10 false LCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false LCB+ 0.573,0.302 1.188,0.5 0.615,0.198 10 false LGND 0.604,1.333 1.219,1.531 0.615,0.198 10 false LCV- 2.49,1.333 3.104,1.531 0.615,0.198 10 false LCV+ 0.333,1.708 0.948,1.906 0.615,0.198 10 false LCV+ 1.552,3.115 2.167,3.313 0.615,0.198 10 false LGND 0.313,3.094 0.927,3.292 0.615,0.198 10 false LCV- 2.667,0.813 3.281,1.01 0.615,0.198 10 false A 2.875,2.281 3.313,2.521 0.438,0.24 10 false O22 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Front view of wire harness connector
(to Vehicle Wire Harness Connector)


Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (LCB+) - O22-2 (LCB+) Always Below 1 Ω
A-5 (LCV+) - O22-1 (LCV+) Always Below 1 Ω
A-7 (LCV-) - O22-12 (LCV-) Always Below 1 Ω
A-3 (LGND) - O22-13 (LGND) Always Below 1 Ω
A-1 (LCB+) or O22-2 (LCB+) - Body ground Always 10 kΩ or higher
A-5 (LCV+) or O22-1 (LCV+) - Body ground Always 10 kΩ or higher
A-7 (LCV-) or O22-12 (LCV-) - Body ground Always 10 kΩ or higher
A-3 (LGND) or O22-13 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

14.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1686 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG