Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0468732 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C168D  Vehicle Information Unmatched  


DESCRIPTION

This DTC is stored if the television camera controller and rear television camera assembly judges as a result of its self check that the vehicle information received via CAN communication and the vehicle information stored in the television camera controller do not match.

Television Camera Controller
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C168D Vehicle Information Unmatched Vehicle information unmatched
·

Camera view adjustment (calibration)

·

Steering angle setting

·

Television camera controller


Circumference Monitoring Camera Control Module

Rear Television Camera Assembly
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C168D Vehicle Information Unmatched Vehicle information unmatched
·

Back camera position setting

·

Steering angle setting

·

Rear Television camera assembly


Rear Camera

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK DTC OUTPUT
a.

Recheck for DTCs and check that no DTCs are output.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
Chassis > Rear Camera > Trouble Codes
50001 85

Result:
Result Proceed to
DTC C168D is output ("Parking Assist Camera") A
DTC C168D is output ("Panoramic View Monitor") B



A

2.PERFORM SETTINGS (BACK CAMERA POSITION SETTING, STEERING ANGLE SETTING)

B

4.PERFORM SETTINGS (CAMERA VIEW ADJUSTMENT [CALIBRATION], STEERING ANGLE SETTING)
2.PERFORM SETTINGS (BACK CAMERA POSITION SETTING, STEERING ANGLE SETTING)
a.

Perform the following procedure depending on the memory conditions to register the vehicle information into the rear television camera assembly.

i.

Refer to rear television camera assembly optical axis adjustment (back camera position setting).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION




Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Clear the DTCs.

Chassis > Rear Camera > Clear DTCs
50002 85

b.

Recheck for DTCs and check that no DTCs are output.

Chassis > Rear Camera > Trouble Codes
50001 85
HINT:
·

If DTC C168D is output, perform the procedure to register the vehicle information into the rear television camera assembly.

·

If DTC C168D is still output after performing the procedure to register the vehicle information into the rear television camera assembly 3 times, replace the rear television camera assembly.




Result:
Result Proceed to
DTC C168D is output A
DTC C168D is not output B



A

B

END

4.PERFORM SETTINGS (CAMERA VIEW ADJUSTMENT [CALIBRATION], STEERING ANGLE SETTING)
a.

Perform the following procedure depending on the memory conditions to register the vehicle information to the television camera controller.




Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C168D is not output.


HINT:
·

If DTC C168D is output, perform the procedure to allow the television camera controller to store the vehicle information again.

·

If DTC C168D is still output after performing the procedure to make the television camera controller store the vehicle information 3 times, replace the television camera controller.




Result:
Proceed to
OK
NG



OK

END (SETTINGS ARE DEFECTIVE)

NG

6.READ VALUE USING GTS
6.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

·

Back Camera Availability Consistency


Chassis > Circumference Monitoring Camera Control Module > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Camera Availability Consistency Status of ECU stored in rear television camera assembly OK/NG OK: Normal
NG: Rear television camera assembly or television camera controller is abnormal
-
Chassis > Circumference Monitoring Camera Control Module > Data List
Tester Display
Back Camera Availability Consistency
50003 353 53
Result:
Result Proceed to
NG is displayed A
OK is displayed B




A

ADJUST PANORAMIC VIEW MONITOR SYSTEM DISPLAY SETTING

B