The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door removal/installation are shown below.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
64718C
2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
74038B
4.REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY
Using a moulding remover, disengage the 3 claws to remove the rear door armrest cover sub-assembly.
5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 clips, 5 claws and 6 guides as shown in the illustration.
Disconnect the connector to remove the rear power window regulator switch assembly with rear door upper armrest base panel.
74260
6.REMOVE REAR ARMREST ASSEMBLY
|
Remove in this Direction |
Disengage the 3 clips, 8 claws and 2 guides as shown in the illustration.
|
Remove in this Direction |
Disengage the guide to remove the rear armrest assembly as shown in the illustration.
67604
7.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
|
Protective Tape |
Apply protective tape to the rear door panel as shown in the illustration.
Remove the 3 screws.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 7 clips as shown in the illustration.
|
Remove in this Direction |
Pull out the rear door trim board sub-assembly as shown in the illustration to disengage the guide.
Raise the rear door trim board sub-assembly to separate the rear door trim board sub-assembly with the rear door inner glass weatherstrip and No. 1 door scuff plate clamp.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
|
Remove in this Direction |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.
Using a screwdriver, disengage the claw to remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly.
68174A
8.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
|
Remove in this Direction |
Slide the rear door inner glass weatherstrip to remove it from the rear door trim board sub-assembly as shown in the illustration.
65907E
9.REMOVE REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)
Remove the 9 screws.
Disengage the 3 guides to remove the rear curtain sub-assembly.
67844A
10.REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
Disengage the clip.
Remove the rear door No. 2 service hole cover.
69206C
11.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 3 claws to remove the rear door inside handle sub-assembly.
86160B
12.REMOVE REAR SPEAKER ASSEMBLY
67674A
13.REMOVE REAR DOOR FRAME GARNISH
Disengage the 2 claws to remove the rear door frame garnish.
67842E
14.REMOVE REAR DOOR SERVICE HOLE COVER
Disconnect the connector.
Disengage the 2 clamps.
Disengage the 8 clips to remove the rear door service hole cover.
67848A
15.REMOVE REAR DOOR NO. 1 VENT SEAL
Remove the rear door No. 1 vent seal.
67858B
16.REMOVE REAR DOOR PANEL PROTECTOR
Disengage the clip.
Remove the rear door panel protector.
68152C
17.REMOVE REAR DOOR GLASS RUN
Remove the rear door glass run.
68640A
18.REMOVE REAR DOOR CHECK ASSEMBLY
|
Nut |
|
Bolt |
Remove the 2 nuts, bolt and rear door check assembly.
67872
19.REMOVE REAR DOOR WEATHERSTRIP
| *a | Double-sided Tape |
Using a clip remover, disengage the 23 clips and remove the rear door weatherstrip.
67408F
20.REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
|
Screw |
|
Bolt |
Remove the screw, 2 bolts and rear door rear lower window frame sub-assembly.
68124B
21.REMOVE REAR DOOR QUARTER WINDOW GLASS
|
Remove in this Direction |
Remove the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
68104
22.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Separate the rear door glass sub-assembly from the rear door window regulator assembly as shown in the illustration.
After separating the rear door glass sub-assembly, do not allow it to fall.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the rear door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
Do not damage the rear door glass sub-assembly.
69906B
23.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY
| *a | Protective Tape |
Using a screwdriver, remove the rear door glass channel sub-assembly.
Tape the screwdriver tip before use.
69975A
24.REMOVE REAR DOOR GLASS CHANNEL FILLER
Remove the rear door glass channel filler from the rear door glass sub-assembly.
25.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY
Disconnect the connector.
| *a | Temporary Bolt |
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.
Remove the 3 bolts and rear door window regulator assembly.
Remove the temporary bolt from the rear door window regulator assembly.
69060A
26.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
69240
27.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
|
Disengage in this Direction |
Disengage the 2 claws and move the lever as shown in the illustration.
|
Remove in this Direction |
Remove the rear door outside handle assembly as shown in the illustration.
69227L
28.REMOVE REAR DOOR OUTSIDE HANDLE COVER
Using a T30 "TORX" socket wrench, loosen the screw.
The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.
Disengage the claw to remove the rear door outside handle cover.
69241G
29.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 3 claws to remove the rear door front outside handle pad.
69242G
30.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
Disengage the claw and 3 guides to remove the rear door rear outside handle pad.
69204A
31.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
| *A | Inside |
| *B | Outside |
Using a T30 "TORX" socket wrench, remove the screw.
Slide the rear door outside handle frame sub-assembly as shown in the illustration to disengage the claw and then remove it.
65923E
32.REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped with protective tape, push out the pin as shown in the illustration.
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped with protective tape, disengage the pin.
|
Push |
Disengage the 4 claws to remove the 2 curtain hooks as shown in the illustration.
67003C
33.REMOVE REAR DOOR PANEL CUSHION
Disengage the 4 claws to remove the 2 rear door panel cushions.
67888F
34.REMOVE REAR DOOR NO. 2 WEATHERSTRIP
Disengage the 5 clips to remove the rear door No. 2 weatherstrip.
75740
35.REMOVE REAR DOOR BELT MOULDING ASSEMBLY
75792
36.REMOVE DOOR WINDOW FRAME MOULDING CLIP
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.
75762A
37.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING
67846A
38.REMOVE REAR DOOR FRONT OUTSIDE SEAL
Disengage the guide to remove the rear door front outside seal.
75708
39.REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY
75978H
40.REMOVE REAR DOOR LOWER OUTSIDE STRIPE
75988C
41.REMOVE REAR DOOR OUTSIDE STRIPE