Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › from 2021.02
RM33C0E _59 Vehicle Exterior _065474 EXTERIOR PANELS / TRIM _0333719 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REASSEMBLY  


PROCEDURE

Hide 52171C 1.INSTALL REAR BUMPER REINFORCEMENT (for Type A)

a.
B483749

Install the rear bumper reinforcement with the 6 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 52171C 2.INSTALL REAR BUMPER REINFORCEMENT (for Type B)

a.
B483752

Install the rear bumper reinforcement with the 6 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 52615 3.INSTALL REAR BUMPER ENERGY ABSORBER (for Type A)

a.
B483748C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides to install the rear bumper energy absorber as shown in the illustration.


Hide 52592 4.INSTALL REAR BUMPER SIDE SEAL LH

a.
B485390

Install the 2 clips.


b.
B473365

Install the rear bumper side seal LH with 2 new grommets.


Hide 52591 5.INSTALL REAR BUMPER SIDE SEAL RH

a.
B490262

Install the 3 clips.


b.
B473366

Install the rear bumper side seal RH with 2 new grommets.


Hide 52563D 6.INSTALL REAR BUMPER UPPER RETAINER LH

a.

Engage the grommet.


b.
B471295

Engage the 2 guides to temporarily install the rear bumper upper retainer LH to the rear combination light assembly LH.


c.
B471296C01
0.531,0.948 0.781,0.74 true 1.177,1.115 1.563,0.885 true 1.604,0.771 1.823,0.979 0.219,0.208 10 true *a 0.792,0.615 1.01,0.823 0.219,0.208 10 true *b
*a Pin
*b Guide
V113147

Install in this Direction


Engage the guide and pin as shown in the illustration to temporarily install the rear bumper upper retainer LH and rear combination light assembly LH as a set.


d.

Install the rear combination light assembly with the 2 screws.


e.

Connect the connector.


f.

Install the rear bumper upper retainer LH with the screw.


Hide 52562E 7.INSTALL REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 52576 8.INSTALL REAR BUMPER SIDE RETAINER LH

a.
B471297C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide as shown in the illustration.


b.

Engage the 2 claws.


c.
B471298C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 clips as shown in the illustration.


d.
B485888

Install the rear bumper side retainer LH with the screw.


Hide 52575 9.INSTALL REAR BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 64722 10.INSTALL LUGGAGE COMPARTMENT TRIM INNER COVER LH

Hide 64721 11.INSTALL LUGGAGE COMPARTMENT TRIM INNER COVER RH

Hide 58387 12.INSTALL REAR FLOOR FINISH PLATE

Hide 64749E 13.INSTALL LUGGAGE COMPARTMENT DOOR STRIKER COVER

Hide 64725D 14.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 64779E 15.INSTALL SPARE WHEEL COVER TRAY

Hide 64770 16.INSTALL SPARE WHEEL COVER ASSEMBLY

Hide 52461F 17.INSTALL REAR BUMPER PAD

HINT:
·

When installing the rear bumper pad, heat the rear bumper cover using a heat light.

·

Use the same procedure for the RH side and LH side.



Heating Temperature
Item Temperature
Rear Bumper Cover 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper cover excessively.


a.

Clean the rear bumper cover surface.

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove any remaining double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new rear bumper pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B470441C01
1.844,0.969 2.167,0.969 true 2.208,0.875 2.427,1.083 0.219,0.208 10 true *a
*a Line


Install the rear bumper pad as shown in the illustration.

HINT:

Press the rear bumper pad firmly to install it.



Hide 52169C 18.INSTALL LOWER REAR BUMPER COVER (for Type A)

a.

Engage the 12 claws.

B470440


b.

Install the 2 clips.

B470439


c.

Install the lower rear bumper cover with the 2 screws.


Hide 52166B 19.INSTALL REAR BUMPER CORNER EXTENSION LH (for Type B)

a.
B488729

Engage the 4 guides and 4 claws to install the rear bumper corner extension LH.


Hide 52165D 20.INSTALL REAR BUMPER CORNER EXTENSION RH (for Type B)

HINT:

Use the same procedure as for the LH side.


Hide 52724 21.INSTALL REAR BUMPER EXTENSION MOULDING LH (for Type B)

a.
B471287

Engage the 4 claws to install the rear bumper extension moulding LH.


Hide 52723 22.INSTALL REAR BUMPER EXTENSION MOULDING RH (for Type B)

HINT:

Use the same procedure as for the LH side.


Hide 81920 23.INSTALL REFLEX REFLECTOR ASSEMBLY LH

a.
B471286

Engage the guide and claw.


b.
B471285

Install the reflex reflector assembly LH with the screw.


Hide 81910 24.INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 25.INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

a.

w/o Parking Support Brake System:

i.

Clean the rear bumper cover.

1.

Remove any remaining double-sided tape from the rear bumper cover.

2.

Wipe off any tape adhesive residue with cleaner.



ii.
B471319C01
0,0 0,0 false
V100144

Primer


Using a brush or felt, apply primer or equivalent to the ultrasonic sensor clip installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper cover until the primer has dried.




iii.

Peel off the release paper from 2 new ultrasonic sensor clips.


iv.

Align the 2 ultrasonic sensor clips with the mark on the rear bumper cover and install it as shown in the illustration.

B489427C01
1.948,0.688 2.354,0.688 true 4.74,0.677 5.146,0.677 true 1.76,0.583 1.979,0.813 0.219,0.229 10 true *a 5.156,0.563 5.375,0.792 0.219,0.229 10 true *a
*a Line - -


NOTICE:
·

Ensure that the ultrasonic sensor clip is within the line.

·

The double-sided tape of an ultrasonic sensor clip will deteriorate if it is detached. Make sure to replace the ultrasonic sensor clip with a new one when reattachment is necessary.



HINT:

Press the ultrasonic sensor clip with a force of 30 N (3.0 kgf) for 3 seconds to install the ultrasonic sensor clip firmly so that there is no clearance between the ultrasonic sensor clip and rear bumper cover.




Hide 82182 26.INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

a.

w/o Parking Support Brake System:

i.

Engage the 2 clamps to install the No. 2 luggage room wire.

B607511



Hide 82182 27.INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

a.

w/ Parking Support Brake System:

i.

Install the No. 2 luggage room wire.



Hide 89348R 28.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89342 29.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89348R 30.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89348S 31.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89342 32.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89342A 33.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)