Home › Suspension › REAR SUSPENSION › REAR TRAILING ARM › from 2021.02
RM33C0E _53 Suspension _065439 REAR SUSPENSION _0331925 REAR TRAILING ARM A

REAR SUSPENSION  REAR TRAILING ARM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear trailing arm assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic View Monitor System (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 58399D 2.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)

a.

for LH Side:

i.
C379124N01
1.969,0.125 2.104,0.302 0.135,0.177 10 true A 2.729,0.76 2.865,0.938 0.135,0.177 10 true B 1.5,0.063 1.635,0.24 0.135,0.177 10 true B 0.552,1.063 0.688,1.24 0.135,0.177 10 true C

Remove the bolt and clip (A).


ii.

Disengage the 2 grommets (B) and clip (C) to remove the No. 2 floor under cover.



Hide 58398F 3.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)

a.

for RH Side:

i.
C379125N01
1.458,0.073 1.635,0.24 0.177,0.167 10 true A 2.115,0.042 2.292,0.208 0.177,0.167 10 true B 0.51,0.75 0.688,0.917 0.177,0.167 10 true B

Remove the bolt and clip (A).


ii.

Disengage the 2 grommets (B) to remove the No. 1 floor under cover.



Hide 890C0A 4.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C376673

Disengage the 2 clamps.


b.

Remove the nut and separate the No. 2 parking brake wire assembly from the rear trailing arm assembly.


Hide 48840A 5.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48780E 6.REMOVE REAR TRAILING ARM ASSEMBLY

a.
C376674C02
0.635,1.49 1.01,1.49 false 1.969,1.719 2.344,1.719 false 0.448,1.417 0.656,1.604 0.208,0.188 10 true *a 2.375,1.646 2.688,1.802 0.313,0.156 10 false *b
*a Wooden Block
*b Transmission Jack


Using a transmission jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.
C376675

Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


c.
C370218

Remove the 4 bolts and rear trailing arm assembly.


Hide 48738 7.REMOVE REAR SUSPENSION ARM COVER

a.
C370219

Secure the rear trailing arm assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C370220

Disengage the 4 claws and remove the rear suspension arm cover.


Hide 48727 8.REMOVE REAR SUSPENSION ARM BRACKET

a.
C370221

Remove the bolt, nut and rear suspension arm bracket from the rear trailing arm assembly.