The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. DISCHARGE FUEL SYSTEM PRESSURE
64718C
3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER
4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
22030
5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
25715
6.REMOVE EMISSION CONTROL VALVE BRACKET (w/ Differential Pressure Sensor)
23910A
7.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly from the fuel pump assembly and fuel delivery pipe with sensor assembly.
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
16278
8.REMOVE NO. 2 WATER BY-PASS PIPE
Disengage the clamp to disconnect the HV air conditioning wire.
Slide the clip and disconnect the No. 8 water by-pass hose from the No. 2 water by-pass pipe.
Using an 8 mm socket wrench, remove the 2 bolts (A) and separate the No. 2 water by-pass pipe from the intake manifold.
Remove the bolt (B) and No. 2 water by-pass pipe from the cylinder block sub-assembly.
23801P
9.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.
Disconnect the ignition coil connector.
|
Union Nut |
|
Bolt |
for EGR Valve Bracket Connection Type:
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
Using an 8 mm socket wrench, remove the bolt.
for Cylinder Head Cover Sub-assembly Connection Type:
|
Union Nut |
|
Bolt |
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
Using an 8 mm socket wrench, remove the bolt.
Loosen the 2 bolts of the fuel pump assembly.
Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.
23100X
10.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY
When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.
Disconnect the fuel pump assembly connector.
Remove the 2 bolts, fuel pump assembly and fuel pump flange from the cylinder head cover sub-assembly.
Remove the O-ring from the fuel pump assembly.
Remove the fuel pump lifter assembly from the fuel pump lifter guide.
Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.