Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER › from 2021.02
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319553 OIL COOLER A

P710 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cooling cooler removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)for Nickel Metal Hydride Battery
(Click here)for Lithium-ion Battery

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION



PROCEDURE

Hide 53851M 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852K 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 53737B 5.REMOVE FRONT FENDER APRON SEAL LH

Hide G9200 6.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide G9225K 7.REMOVE NO. 1 INVERTER COOLING HOSE

a.
C381413

Slide the clip and remove the No. 1 inverter cooling hose from the motor cooling cooler.


Hide G9229A 8.DISCONNECT NO. 5 INVERTER COOLING HOSE

Hide G125A 9.REMOVE MOTOR COOLING COOLER

a.
C381414C01
1.927,0.24 2.073,0.24 2.073,0.24 2.24,0.479 true 1.125,0.604 1.271,0.604 1.271,0.604 1.438,0.844 true 1.698,0.177 1.906,0.354 0.208,0.177 10 true *1 0.896,0.542 1.125,0.719 0.229,0.177 10 true *2
*1 Oil Cooler Union Bolt
*2 No. 1 Oil Cooler Tube Clamp


Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


b.

Remove the bolt and No. 1 oil cooler tube clamp to disconnect No. 2 motor cooling pipe from the hose bracket.


c.
C381415

Remove the 3 bolts to disconnect the motor cooling cooler from the No. 1 transmission control cable bracket.


d.
C377456

Slide the clip and disconnect the No. 1 motor cooling hose from the transaxle housing tube connector.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.



Hide G1252A 10.REMOVE NO. 2 MOTOR COOLING PIPE

a.
C381416

Slide the clip and remove the No. 2 motor cooling pipe from the No. 2 motor cooling hose.

NOTICE:

Make sure not to remove the No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.