The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Roof console box sub-assembly ·
Telephone microphone assembly ·
Radio and display receiver assembly ·
Telematics transceiver* ·
Harness or connector |
*: w/ Telematics Transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Sliding Roof) | A |
| OK (w/o Sliding Roof and w/o Telematics Transceiver) | B |
| OK (w/o Sliding Roof and w/ Telematics Transceiver) | C |
| NG | D |
A
B
C
D
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V14 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V14-6 (SNS2) | Always | Below 1 Ω |
| K2-22 (MIN-) - V14-7 (MCO-) | Always | Below 1 Ω |
| K2-25 (SNS2) or V14-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or V14-7 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - V14-6 (SNS2) | Always | Below 1 Ω |
| B-2 - V14-7 (MCO-) | Always | Below 1 Ω |
| B-1 or V14-6 (SNS2) - V14-15 (GND) | Always | 10 kΩ or higher |
| B-2 or V14-7 (MCO-) - V14-15 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V12 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V12-12 (SNS2) | Always | Below 1 Ω |
| K2-22 (MIN-) - V12-11 (MCO-) | Always | Below 1 Ω |
| K2-25 (SNS2) or V12-12 (SNS2) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or V12-11 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (SNS2) - 11 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - V12-12 (SNS2) | Always | Below 1 Ω |
| B-2 - V12-11 (MCO-) | Always | Below 1 Ω |
| B-1 or V12-12 (SNS2) - V12-4 (GND) | Always | 10 kΩ or higher |
| B-2 or V12-11 (MCO-) - V12-4 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K151 telematics transceiver connector.
Disconnect the V18 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K151-7 (MCI-) - V18-4 (MCO-) | Always | Below 1 Ω |
| K151-7 (MCI-) or V18-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the K151 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-22 (MIN-) - K151-32 (MCO-) | Always | Below 1 Ω |
| K2-22 (MIN-) or K151-32 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V18 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V18-3 (SNS2) | Always | Below 1 Ω |
| K2-25 (SNS2) or V18-3 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K151 telematics transceiver connector.
Connect the K2 radio and display receiver assembly connector.
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K151-7 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - V18-3 (SNS2) | Always | Below 1 Ω |
| B-2 - V18-4 (MCO-) | Always | Below 1 Ω |
| B-1 or V18-3 (SNS2) - V18-11 (GND) | Always | 10 kΩ or higher |
| B-2 or V18-4 (MCO-) - V18-11 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG