w/o Telematics Transceiver:
The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.
w/ Telematics Transceiver:
The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the telematics transceiver sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the telematics transceiver.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Result | Proceed to |
|---|---|
| NG (w/ Sliding Roof) | A |
| NG (w/o Sliding Roof and w/o Telematics Transceiver) | B |
| NG (w/o Sliding Roof and w/ Telematics Transceiver) | C |
| OK | D |
A
B
C
D
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V14 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V14-6 (SNS2) | Always | Below 1 Ω |
| K2-23 (MACC) - V14-9 (MACC) | Always | Below 1 Ω |
| K2-21 (MIN+) - V14-8 (MCO+) | Always | Below 1 Ω |
| K2-22 (MIN-) - V14-7 (MCO-) | Always | Below 1 Ω |
| K2-25 (SNS2) or V14-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| K2-23 (MACC) or V14-9 (MACC) - Body ground | Always | 10 kΩ or higher |
| K2-21 (MIN+) or V14-8 (MCO+) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or V14-7 (MCO-) - Body ground | Always | 10 kΩ or higher |
| K2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V14 roof console box sub-assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-23 (MACC) - Body ground | Power switch on (ACC) | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-24 (SGND) - Body ground | Always | Below 1 Ω |
| K2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V14 roof console box sub-assembly connector.
Turn the power switch on (ACC).
| *a | Component with harness connected
(Roof Console Box Sub-assembly) |
Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the V14 roof console box sub-assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V14-8 (MCO+) - V14-7 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the power switch on (ACC). 2.
Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V14-8 (MCO+) - B-3 | Always | Below 1 Ω |
| V14-7 (MCO-) - B-2 | Always | Below 1 Ω |
| V14-8 (MCO+) or B-3 - V14-15 (GND) | Always | 10 kΩ or higher |
| V14-7 (MCO-) or B-2 - V14-15 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V14-6 (SNS2) - B-1 | Always | Below 1 Ω |
| V14-7 (MCO-) - B-2 | Always | Below 1 Ω |
| V14-6 (SNS2) or B-1 - V14-15 (GND) | Always | 10 kΩ or higher |
| V14-7 (MCO-) or B-2 - V14-15 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V12 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V12-12 (SNS2) | Always | Below 1 Ω |
| K2-23 (MACC) - V12-9 (MACC) | Always | Below 1 Ω |
| K2-21 (MIN+) - V12-10 (MCO+) | Always | Below 1 Ω |
| K2-22 (MIN-) - V12-11 (MCO-) | Always | Below 1 Ω |
| K2-25 (SNS2) or V12-12 (SNS2) - Body ground | Always | 10 kΩ or higher |
| K2-23 (MACC) or V12-9 (MACC) - Body ground | Always | 10 kΩ or higher |
| K2-21 (MIN+) or V12-10 (MCO+) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or V12-11 (MCO-) - Body ground | Always | 10 kΩ or higher |
| K2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V12 roof console box sub-assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-23 (MACC) - Body ground | Power switch on (ACC) | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-24 (SGND) - Body ground | Always | Below 1 Ω |
| K2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (SNS2) - 11 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V12 roof console box sub-assembly connector.
Turn the power switch on (ACC).
| *a | Component with harness connected
(Roof Console Box Sub-assembly) |
Connect an oscilloscope to terminals 10 (MCO+) and 11 (MCO-) of the V12 roof console box sub-assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V12-10 (MCO+) - V12-11 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the power switch on (ACC). 2.
Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V12-10 (MCO+) - B-3 | Always | Below 1 Ω |
| V12-11 (MCO-) - B-2 | Always | Below 1 Ω |
| V12-10 (MCO+) or B-3 - V12-4 (GND) | Always | 10 kΩ or higher |
| V12-11 (MCO-) or B-2 - V12-4 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V12-12 (SNS2) - B-1 | Always | Below 1 Ω |
| V12-11 (MCO-) - B-2 | Always | Below 1 Ω |
| V12-12 (SNS2) or B-1 - V12-4 (GND) | Always | 10 kΩ or higher |
| V12-11 (MCO-) or B-2 - V12-4 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V18 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V18-3 (SNS2) | Always | Below 1 Ω |
| K2-25 (SNS2) or V18-3 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the K151 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-21 (MIN+) - K151-16 (MCO+) | Always | Below 1 Ω |
| K2-22 (MIN-) - K151-32 (MCO-) | Always | Below 1 Ω |
| K2-21 (MIN+) or K151-16 (MCO+) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or K151-32 (MCO-) - Body ground | Always | 10 kΩ or higher |
| K2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K151 telematics transceiver connector.
Disconnect the V18 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K151-5 (MCVD) - V18-6 (MACC) | Always | Below 1 Ω |
| K151-6 (MCI+) - V18-5 (MCO+) | Always | Below 1 Ω |
| K151-7 (MCI-) - V18-4 (MCO-) | Always | Below 1 Ω |
| K151-5 (MCVD) or V18-6 (MACC) - Body ground | Always | 10 kΩ or higher |
| K151-6 (MCI+) or V18-5 (MCO+) - Body ground | Always | 10 kΩ or higher |
| K151-7 (MCI-) or V18-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| K151-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K151 telematics transceiver connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Connect the K2 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-24 (SGND) - Body ground | Always | Below 1 Ω |
| K2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K151 telematics transceiver connector.
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K151-5 (MCVD) - Body ground | Power switch on (ACC) | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K151-7 (MCI-) - Body ground | Always | Below 1 Ω |
| K151-23 (SGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V18 roof console box sub-assembly connector.
Turn the power switch on (ACC).
| *a | Component with harness connected
(Roof Console Box Sub-assembly) |
Connect an oscilloscope to terminals 5 (MCO+) and 4 (MCO-) of the V18 roof console box sub-assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V18-5 (MCO+) - V18-4 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the power switch on (ACC). 2.
Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V18 roof console box sub-assembly connector.
Connect the K151 telematics transceiver connector.
Turn the power switch on (ACC).
| *a | Component with harness connected
(Telematics Transceiver) |
Connect an oscilloscope to terminals 16 (MCO+) and 32 (MCO-) of the K151 telematics transceiver connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | K151-16 (MCO+) - K151-32 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the power switch on (ACC). 2.
Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V18-5 (MCO+) - B-3 | Always | Below 1 Ω |
| V18-4 (MCO-) - B-2 | Always | Below 1 Ω |
| V18-5 (MCO+) or B-3 - V18-11 (GND) | Always | 10 kΩ or higher |
| V18-4 (MCO-) or B-2 - V18-11 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V18-3 (SNS2) - B-1 | Always | Below 1 Ω |
| V18-4 (MCO-) - B-2 | Always | Below 1 Ω |
| V18-3 (SNS2) or B-1 - V18-11 (GND) | Always | 10 kΩ or higher |
| V18-4 (MCO-) or B-2 - V18-11 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG