Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY) › from 2021.02
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442444 HV RELAY ASSEMBLY(for LITHIUM-ION BATTERY) A

HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY(for LITHIUM-ION BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery junction block assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of HV battery junction block assembly Current sensor offset learning DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types ofmemory and settings. As a result, after turning the power switch off, make sure to wait at least 85seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 82111 2.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 82111 6.CONNECT ENGINE ROOM MAIN WIRE

Hide 73350C 7.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 8.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 9.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 10.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 11.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 12.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 13.REMOVE REAR UNDER SIDE COVER RH

Hide 71033 15.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide 821H1 17.DISCONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406748C02
1.885,1.271 2.375,1.271 true 2.385,1.177 2.594,1.344 0.208,0.167 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.

Disconnect the shield ground from the HV battery.


Hide G92Z0 19.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A391099

Disengage the 2 claws and open the wiring harness protector.


b.
A391100

Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



c.

Disconnect the hybrid battery terminal block connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



d.
A391101

Remove the bolt and electric vehicle battery plug assembly from the HV battery.


e.
A391102

Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate the disconnected high-voltage connectors with insulating tape.



f.
A391103C02
2.802,2.594 2.906,2.74 2.906,2.74 3.135,2.74 true 3.177,2.667 3.385,2.865 0.208,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the wiring harness protector.


g.
A391104

Remove the 4 nuts and HV battery junction block assembly from the HV battery.

NOTICE:

If the HV battery junction block assembly has been struck or dropped, replace it with a new one.