Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0328993 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  INSTALLATION  


PROCEDURE

Hide 821H1 1.INSTALL FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406743

Insert the HV floor under wire into the floor panel hole and engage the grommet.


b.
A406766C02
1.333,1.365 1.49,1.563 0.156,0.198 10 true 1 0.854,0.573 1.01,0.771 0.156,0.198 10 true 2

Install 2 new clamps in the order shown in the illustration.


c.
A406767

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.
A406745C02
3.031,0.99 3.188,1.188 0.156,0.198 10 true 1 1.906,1.094 2.063,1.292 0.156,0.198 10 true 2 0.677,0.979 0.833,1.177 0.156,0.198 10 true 3

Install the 2 nuts and new clamp in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
A406746

Install the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Connect the HV floor under wire connector.


g.

Engage the clamp.


h.
A406768

Install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


i.
A406765

Install the HV floor under wire with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 58223 3.INSTALL CENTER NO. 2 FLOOR HEAT INSULATOR

a.

Install the center No. 2 floor heat insulator with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 58398F 4.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 821H1 7.CONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the floor wire connector.


b.

Connect the shield ground to the HV battery.


c.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 8.INSTALL NO. 1 HV BATTERY COVER PANEL RH

Hide 71033 9.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide 76974F 11.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 12.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 13.INSTALL REAR UNDER SIDE COVER RH

Hide 67917A 14.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72693 15.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 16.INSTALL REAR SEAT CUSHION ASSEMBLY

Hide 73350C 17.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 82111 19.CONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A406212

Connect the inverter with converter assembly connector and move the lock lever to lock them.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connectors.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.