Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _078700 TELEMATICS _0387130 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B157213  Microphone Circuit Open  


DESCRIPTION

This DTC is stored when a communication telematics box signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157213 Microphone Circuit Open Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telematics transceiver

·

Mayday wire

·

Communication telematics box

·

Harness or connector



WIRING DIAGRAM

E388577E10
0.906,1.406 1.521,1.604 0.615,0.198 10 false MCMD 1.052,1.813 1.667,2.01 0.615,0.198 10 false SP+ 1.063,2.219 1.677,2.417 0.615,0.198 10 false SP- 0.99,2.594 1.604,2.792 0.615,0.198 10 false MICV 0.948,2.99 1.563,3.188 0.615,0.198 10 false MIC1+ 0.948,3.375 1.563,3.573 0.615,0.198 10 false MIC2+ 1.042,3.792 1.656,3.99 0.615,0.198 10 false MCI- 5.802,1.396 6.417,1.594 0.615,0.198 10 false MCMD 5.813,1.781 6.427,1.979 0.615,0.198 10 false SP+ 5.823,2.198 6.438,2.396 0.615,0.198 10 false SP- 5.802,2.583 6.417,2.781 0.615,0.198 10 false MICV 5.802,3 6.417,3.198 0.615,0.198 10 false MCVD 5.802,3.365 6.417,3.563 0.615,0.198 10 false MCI+ 5.813,3.771 6.427,3.969 0.615,0.198 10 false MCI- 5.906,4.604 6.677,5.01 0.771,0.406 10 false Telematics Transceiver 5.396,3.76 6.167,4.167 0.771,0.406 10 false K151 3.823,3.969 4.688,4.219 0.865,0.25 10 false (Shielded) 0.375,4.75 1.438,5.156 1.063,0.406 10 false Communication Telematics Box 0.375,4.583 1.146,4.99 0.771,0.406 10 false P 2.01,1.302 2.625,1.5 0.615,0.198 10 false MCMD 2.146,1.698 2.76,1.896 0.615,0.198 10 false SP+ 2.188,2.104 2.802,2.302 0.615,0.198 10 false SP- 2.083,2.479 2.698,2.677 0.615,0.198 10 false MICV 2.104,2.896 2.719,3.094 0.615,0.198 10 false MIC1 2.104,3.281 2.719,3.479 0.615,0.198 10 false MIC2 2.125,3.677 2.74,3.875 0.615,0.198 10 false MCI- 1.458,1.313 2.073,1.51 0.615,0.198 10 false 1 1.479,1.708 2.094,1.906 0.615,0.198 10 false 3 1.469,2.104 2.083,2.302 0.615,0.198 10 false 8 1.479,2.5 2.094,2.698 0.615,0.198 10 false 5 1.49,2.865 2.104,3.063 0.615,0.198 10 false 2 1.479,3.25 2.094,3.448 0.615,0.198 10 false 7 1.49,3.677 2.104,3.875 0.615,0.198 10 false 4 2.625,1.219 3.24,1.417 0.615,0.198 10 false 1 2.646,1.615 3.26,1.813 0.615,0.198 10 false 3 2.625,2 3.24,2.198 0.615,0.198 10 false 9 2.635,2.406 3.25,2.604 0.615,0.198 10 false 6 2.594,2.792 3.208,2.99 0.615,0.198 10 false 10 2.594,3.198 3.208,3.396 0.615,0.198 10 false 11 2.635,3.594 3.25,3.792 0.615,0.198 10 false 5 5.469,1.615 6.083,1.813 0.615,0.198 10 false 18 5.521,1.208 6.135,1.406 0.615,0.198 10 false 8 5.469,2 6.083,2.198 0.615,0.198 10 false 34 5.479,2.396 6.094,2.594 0.615,0.198 10 false 24 5.521,2.792 6.146,2.99 0.625,0.198 10 false 5 5.521,3.177 6.146,3.375 0.625,0.198 10 false 6 5.521,3.583 6.146,3.781 0.625,0.198 10 false 7 5.406,3.385 6.177,3.792 0.771,0.406 10 false K151 5.406,2.99 6.177,3.396 0.771,0.406 10 false K151 5.396,2.594 6.167,3 0.771,0.406 10 false K151 5.406,2.188 6.177,2.594 0.771,0.406 10 false K151 5.417,1.792 6.188,2.198 0.771,0.406 10 false K151 5.406,1.396 6.177,1.802 0.771,0.406 10 false K151 2.552,3.771 3.323,4.177 0.771,0.406 10 false V19 2.552,3.375 3.323,3.781 0.771,0.406 10 false V19 2.563,2.969 3.333,3.375 0.771,0.406 10 false V19 2.552,2.594 3.323,3 0.771,0.406 10 false V19 2.563,2.188 3.333,2.594 0.771,0.406 10 false V19 2.563,1.802 3.333,2.208 0.771,0.406 10 false V19 2.552,1.396 3.323,1.802 0.771,0.406 10 false V19 5.771,4.208 6.385,4.406 0.615,0.198 10 false SGND 5.396,4.198 6.167,4.604 0.771,0.406 10 false K151 5.479,4.021 6.104,4.219 0.625,0.198 10 false 23 1.698,4.625 2.469,5.031 0.771,0.406 10 false Mayday Wire

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

f.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEMATICS TRANSCEIVER
2.INSPECT TELEMATICS TRANSCEIVER
a.
E442560C15
2.26,1.948 2.458,2.74 2.458,2.74 2.625,2.74 true 2.292,1.813 2.563,0.969 2.563,0.969 2.729,0.969 true 0.25,0.302 0.563,0.5 0.313,0.198 10 false *a 2.802,0.896 3.344,1.115 0.542,0.219 10 false MCI- 2.677,2.667 3.219,2.885 0.542,0.219 10 false MICV
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
24 (MICV) - Body ground Ignition switch ACC 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAYDAY WIRE)

NG

6.REPLACE TELEMATICS TRANSCEIVER
3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAYDAY WIRE)
a.

Disconnect the K151 telematics transceiver connector.


b.

Disconnect the V19 mayday wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K151-8 (MCMD) - V19-1 (MCMD) Always Below 1 Ω
K151-18 (SP+) - V19-3 (SP+) Always Below 1 Ω
K151-34 (SP-) - V19-9 (SP-) Always Below 1 Ω
K151-24 (MICV) - V19-6 (MICV) Always Below 1 Ω
K151-5 (MCVD) - V19-10 (MIC1) Always Below 1 Ω
K151-6 (MCI+) - V19-11 (MIC2) Always Below 1 Ω
K151-7 (MCI-) - V19-5 (MCI-) Always Below 1 Ω
K151-8 (MCMD) or V19-1 (MCMD) - Body ground Always 10 kΩ or higher
K151-18 (SP+) or V19-3 (SP+) - Body ground Always 10 kΩ or higher
K151-34 (SP-) or V19-9 (SP-) - Body ground Always 10 kΩ or higher
K151-24 (MICV) or V19-6 (MICV) - Body ground Always 10 kΩ or higher
K151-5 (MCVD) or V19-10 (MIC1) - Body ground Always 10 kΩ or higher
K151-6 (MCI+) or V19-11 (MIC2) - Body ground Always 10 kΩ or higher
K151-7 (MCI-) or V19-5 (MCI-) - Body ground Always 10 kΩ or higher
K151-23 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)
a.
E409641C13
1.49,2.823 1.865,3.083 0.375,0.26 1.521,0.365 1.896,0.625 0.375,0.26 2.177,1.281 2.646,1.281 true 1.313,3.208 1.708,3.729 true 1.823,1.271 2.542,0.708 true 1.823,1.604 2.479,2.031 true 0.781,1.292 1.208,1.292 true 1.583,1.615 0.938,2.177 true 1.385,1.583 0.906,1.792 true 1.406,1.219 0.896,0.917 true 1,3.396 1.49,3.729 true 0.917,3.771 1.302,3.771 true 1.719,4 1.854,4.365 true 2.25,3.292 1.917,3.719 true 1.313,4.333 1.531,3.979 true 2.5,3.76 2.073,3.76 true 0.365,2.635 0.677,2.833 0.313,0.198 10 false *b 0.292,0.26 0.604,0.458 0.313,0.198 10 false *a 1.646,2.865 1.958,3.063 0.313,0.198 10 false P 1.583,0.406 1.896,0.604 0.313,0.198 10 false V19 2.688,1.208 3.271,1.583 0.583,0.375 10 false MCMD 0.448,3.688 1.031,4.063 0.583,0.375 10 false MCMD 2.583,0.625 3.167,1 0.583,0.375 10 false SP+ 2.531,1.969 3.115,2.344 0.583,0.375 10 false SP- 0.417,1.219 1,1.594 0.583,0.375 10 false MICV 0.552,1.729 1.052,2.083 0.5,0.354 10 false MIC2 0.563,0.823 1.146,1.198 0.583,0.375 10 false MCI- 0.604,2.167 1.188,2.542 0.583,0.375 10 false MIC1 1.063,3.063 1.646,3.438 0.583,0.375 10 false SP+ 0.563,3.313 1.146,3.688 0.583,0.375 10 false MIC1+ 1.896,4.323 2.531,4.656 0.635,0.333 10 false SP- 2.542,3.698 3.125,4.073 0.583,0.375 10 false MICV 0.927,4.313 1.427,4.667 0.5,0.354 10 false MIC2+ 2.229,3.135 2.813,3.51 0.583,0.375 10 false MCI-
*a Component without harness connected
(Wire Harness)
*b Component without harness connected
(Communication Telematics Box)


Disconnect the V19 wire harness connector.


b.

Disconnect the P communication telematics box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V19-1 (MCMD) - P-1 (MCMD) Always Below 1 Ω
V19-3 (SP+) - P-3 (SP+) Always Below 1 Ω
V19-9 (SP-) - P-8 (SP-) Always Below 1 Ω
V19-6 (MICV) - P-5 (MICV) Always Below 1 Ω
V19-10 (MIC1) - P-2 (MIC1+) Always Below 1 Ω
V19-11 (MIC2) - P-7 (MIC2+) Always Below 1 Ω
V19-5 (MCI-) - P-4 (MCI-) Always Below 1 Ω
V19-1 (MCMD) or P-1 (MCMD) - Body ground Always 10 kΩ or higher
V19-3 (SP+) or P-3 (SP+) - Body ground Always 10 kΩ or higher
V19-9 (SP-) or P-8 (SP-) - Body ground Always 10 kΩ or higher
V19-6 (MICV) or P-5 (MICV) - Body ground Always 10 kΩ or higher
V19-10 (MIC1) or P-2 (MIC1+) - Body ground Always 10 kΩ or higher
V19-11 (MIC2) or P-7 (MIC2+) - Body ground Always 10 kΩ or higher
V19-5 (MCI-) or P-4 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE COMMUNICATION TELEMATICS BOX

NG

5.REPLACE COMMUNICATION TELEMATICS BOX
a.

Replace the communication telematics box with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT